Siemens CP 1243-8 IRC Скачать руководство пользователя страница 34

Страница: 34 / 140

LEDs and connectors

2.2 LEDs

CP 1243-8 IRC

Operating Instructions, 06/2015, C79000-G8976-C385-01

DIAG

(red / green)

LINK

(red / green)

CONNECT

ETH

(green)

VPN

(green)

CONNECT

RS232

(green)

Meaning
(if more than one point listed: alternative

meaning)

green

Configuration of the telecontrol communica-

tion via both interfaces error-free and ena-

bled.
At least one connection established on eve-

ry interface but not all.

flashing

green

Configuration of the telecontrol communica-

tion via both interfaces error-free and ena-

bled. No connection established

flashing

green

Configuration of the telecontrol communica-

tion via both interfaces error-free and ena-

bled.
Connection established via Ethernet to at

least one partner.
No connection established via the serial

interface.

flashing

green

Configuration of the telecontrol communica-

tion via both interfaces error-free and ena-

bled.
Connection established via the serial inter-

face to at least one partner.
No connection established via Ethernet.

VPN connections

All configured VPN connections are estab-

lished.

Not all configured VPN connections are

established.

No VPN connection configured on the CP.

Loading firmware

flashing green

Loading firmware. The "DIAG" LED flashes

alternately red and green.

flashing

green (2x)

flashing green

Firmware was successfully loaded. Die LED

"DIAG" flashes green twice.

flashing red

flashing green

Error loading the firmware

Remedy: Power OFF → ON

* With configured dial-up network connections, a connection is shown as being established or the partner as being reacha-

ble if the connection has been established and least once and then not aborted.

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды