Siemens CP 1243-8 IRC Скачать руководство пользователя страница 122

Страница: 122 / 140

Accessories

C.1 TS modules

CP 1243-8 IRC

122

Operating Instructions, 06/2015, C79000-G8976-C385-01

Specifications

●

Dimensions (WHD): 30 x 100 x 75 mm

●

Weight: 100 g

●

Type of traffic: Full duplex

●

Transmission mode: Asynchronous

●

Signals: TXD, RXD, DSR, CTS, RTS, DTR, DCD

●

Transmission speed: 2400...115200 bps

●

Frame format: 8 data bits (LSB first), no parity bit, 1 stop bit

●

Standard: RS-232

●

D-sub male connector: 9-pin, male (PC COMx)

C.1.5

TS Module GSM

Note
The device is designed for industrial use.

Product package

Designation

Article number

TS Module GSM

6GK7 972-0MG00-0XA0

Properties

The TS Module GSM has an interface for the connection of a GSM/GPRS antenna and a

tray for a SIM card.
The antenna connection and the slot for the SIM card are located behind the lower front

panel.

Accessories

For the antenna, refer to the section Antenna (Page 129).

CSD data connection (Circuit Switched Data)

For outgoing calls, the TS Module GSM supports GPRS and CSD data connections.
For incoming calls, only CSD data connections are accepted.

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды