Siemens CP 1243-8 IRC Скачать руководство пользователя страница 129

Страница: 129 / 140

Accessories

C.3 Antenna

CP 1243-8 IRC
Operating Instructions, 06/2015, C79000-G8976-C385-01

129

●

Communications partners of the MD720 for SMS messages:
–

Mobile phone

–

Fax machine (when using a gateway)

The MD720 operates in terminal mode.

●

Communications partners of the MD720 installed in an S7-200:
–

Engineering station with STEP 7-Micro/WIN
(via GSM network, ISDN network, analog dial-up network)

The MD720 operates in terminal mode.

●

Communications partners of the MD720 installed in an S7-300/400 with TIM:
–

SIMATIC S7-300/400 with TIM module (including classic)
(via GSM network, ISDN network, analog dial-up network)

The MD720 operates in terminal mode.

Connection resources

●

Active connections at runtime
At runtime, the MD720 can connect to 1 communications partner.
The connection partner is configured in the program blocks.

C.3

Antenna

The following antenna is available for use in mobile wireless networks and can be installed

both indoors and outdoors. The antenna must be ordered separately.

Antenna ANT794-4MR

Figure C-6 Antenna ANT794-4MR

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Бренды по названию

Популярные бренды