Siemens CP 1243-8 IRC Скачать руководство пользователя страница 42

Страница: 42 / 140

Installation, connecting up, commissioning

3.2 Installing, connecting up and commissioning

CP 1243-8 IRC

Operating Instructions, 06/2015, C79000-G8976-C385-01

CAUTION

Ground the connecting cable of a TS module separately
Connect the connecting cable of a TS module to the periphery (e.g. modem) separately to

functional ground.

Note
Prior to mounting a TS module
For information on mounting a TS module, also read the appropriate sections in the device

manual, see /4/ (Page 136).

Note
Power supply from the power outputs of the CPU
The external power supply of the CP must be supplied via the power outputs of the CPU for

the sensor supply.
Keep within the maximum load of the power output of the CPU, see /1/ (Page 135).
You will find data relating to the current consumption and power loss of the CP in the section

Technical data (Page 105).

Note
Turning off the station when plugging/pulling the CP
Do not only turn off the power supply to the CP. Always turn off the power supply for the

entire station.

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды