Siemens CP 1243-8 IRC Скачать руководство пользователя страница 44

Страница: 44 / 140

Installation, connecting up, commissioning

3.2 Installing, connecting up and commissioning

CP 1243-8 IRC

Operating Instructions, 06/2015, C79000-G8976-C385-01

Commissioning the module

The remaining steps in commissioning involve downloading the STEP 7 project data. One

requirement for the full commissioning of the module is the completeness of the STEP 7

project data, see Configuration and operation (Page 45).
The STEP 7 project data of the CP is transferred when you load to the station. To load the

station, connect the engineering station on which the project data is located to the Ethernet

interface of the CPU.
You will find more detailed information on loading in the following sections of the STEP 7

information system:

●

“Loading project data"

●

“Using online and diagnostics functions"

Dismantling

WARNING

Keep to the order when dismantling
Remove the plugs of the data cable from the TS module and from the CP before you

remove the power plug from the CP and therefore disconnect the ground connection of the

devices.

Pull down the two lower DIN rail clamps on the rear of the devices with a slotted

screwdriver.
This releases the locking mechanism.

Swing the devices out of the DIN rail profile to the front.

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Бренды по названию

Популярные бренды