Siemens CP 1243-8 IRC Скачать руководство пользователя страница 67

Страница: 67 / 140

Configuration and operation

4.7 Configuration in STEP 7 Basic

CP 1243-8 IRC
Operating Instructions, 06/2015, C79000-G8976-C385-01

4.7.8

Parameter group "SNMP"

SNMP (Simple Network Management Protocol)

SNMP is a protocol for managing networks and nodes in the network. To transmit data,

SNMP uses the connectionless UDP protocol.
The information on the properties of SNMP-compliant devices is entered in MIB files (MIB =

Management Information Base).

Range of performance of the CP as an SNMP agent

The CP supports data queries in the following SNMP versions:

●

SNMPv1 (standard)

●

SNMPv3 (Security)

It returns the contents of MIB objects of the standard MIB II according to RFC 1213 and the

Siemens Automation MIB.

●

MIB II
The CP supports the following groups of MIB objects:
–

System

–

Interfaces
The "Interfaces" MIB object provides status information about the CP interfaces.

–

IP (IPv4 and IPv6)

–

ICMP

–

TCP

–

UDP

–

SNMP

The other groups of the MIB II standard are not supported:
–

Address Translation (AT)

–

EGP

–

Transmission

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды