Siemens CP 1243-8 IRC Скачать руководство пользователя страница 97

Страница: 97 / 140

CP 1243-8 IRC
Operating Instructions, 06/2015, C79000-G8976-C385-01

Programming the program blocks (OUC)

5.1

Program blocks for OUC

Using the program blocks for Open User Communication (OUC)

The instructions (program blocks) listed below are required for direct communication

between S7 stations via Ethernet.
In contrast to other communication types, Open User Communication does not need to be

enabled in the configuration of the CP because corresponding program blocks need to be

created for this. You will find details on the program blocks in the information system of

STEP 7.
To useOpen User Communication, the CP requires a fixed configured IP address.

Note
Different program block versions
Note that in STEP 7 you cannot use different versions of a program block in a station.

Supported program blocks for OUC

The following instructions in the specified minimum version are available for programming

Open User Communication:

●

TSEND_C V3.0 / TRCV_C V3.0
Compact blocks for connection establishment/termination and sending / connection

establishment/termination and receiving
Transfer of data
or

●

TCON V4.0 / TDISCON V2.1
Connection establishment / connection termination

●

TUSEND V4.0 / TURCV V4.0
Sending and receiving data via UDP

●

TSEND V4.0 / TRCV V4.0
Sending and receiving data via TCP or ISOonTCP

●

TMAIL_C V4.0
Sending e-mails

The program block can be found in STEP 7 in the "Instructions > Communication > Open

User Communication" window.

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды