e. IO MENU
PARALLEL
ON
∗
, OFF
If PARALLEL = ON, enable the use of the parallel port. If PARALLEL = OFF,
disable the use of the parallel port.
EMULATION
(EX only)
PCL, PS2, AUTO
∗
Sets the default printer language for parallel port. If EMU = Auto the stream of
data being sent to the printing will be analyzed to determine which language is
being used by the printer job. The printer will be automatically switched to that
language. If PCL or PS2 is selected only that emulation will be used.
HIGH SPEED
ON
∗
, OFF
If HIGH SPEED = ON, the printer receives the data on high speed (use
IEEE1284 Standard Mode).
If HIGH SPEED = OFF, the printer receives the standard mode (IEEE1284
Classic Mode).
ADV FNCTNS
ON
∗
, OFF
If ADV FNCTNS = ON, enable bi-directional parallel communication which
allows the printer to send status readback message to the computer.
SERIAL
ON
∗
, OFF
If SERIAL = ON, enable the use of serial port. If SERIAL = OFF, disable the
use of serial port.
BAUDRATE
1200, 2400, 4800, 9600
∗
, 19200,
38400, 57600
Sets the baud rate for the serial port.
DATA BIT
8
∗
, 7
Sets the data length for the serial port.
PARITY
NON
∗
, EVN, ODD
Sets the parity mode for the serial port.
HANDSHK (Flow)
DTR/DSR
∗
, XON/XOFF
Sets the way of hand shake for the serial port.
DTR POLARITY
HI, LO
∗
Sets the DTR polarity for the serial port.
LOCALTALK
ON
∗
, OFF
If LOCALTALK = ON, enable the use of LocalTalk port.
If LOCALTALK = OFF, disable the use of LocalTalk port.
EMULATION
PS2
∗
Sets the default printer language for the LocalTalk port. However, Mac
environment support only PS, This Menu always sets PS2 mode.
NETWORK
ON
∗
, OFF
If NETWORK = ON, enable the use of the Ethernet port.
If NETWORK = OFF, disable the use of the Ethernet port.
(
∗
indicates factory default value)
f. TEST PRINT Menu
SETTING LIST
Print the TEST PAGE.
PCL FONT LIST
Print the PCL font list sample on the page
PS FONT LIST
Print the font list sample
PCL DEMO PAGE
Print the PCL demo page on the page
PS DEMO PAGE
Print the demo page
g. Special Key Operation
While pressing the key corresponding to each mode, turn on the power switch to execute the job in the mode.
By pressing the keys in the following combinations while power on, the corresponding initial settings are performed.
KEY Operation
Mode
Description
ü
+ ENTER
COLD RESET AU
After power on, "COLD RESET" is shown on LCD and values in "14-10. Factory Default Setting 120"
are set to EEPROM and the printer goes to normal operation. (The EEPROM data on the ICU PWB
are set to the default values.)
MENU +
é
TOP MARGIN
LEFT MARGIN
Top margin and left margin are set by key operation.
LINE + RESET
COLD RESET BG
After power on, "COLD RESET" is shown on LCD and values in "14-10. Factory Default Setting 220"
are set to EEPROM and the printer goes to normal operation. (The EEPROM data on the ICU PWB
are set to the default values.)
RESET + ITEM
COLD RESET JA
After power on, "COLD RESET" is shown on LCD and values in "14-10. Factory Default Setting 220"
are set to EEPROM and the printer goes to normal operation. (The EEPROM data on the ICU PWB
are set to the default values.)
OFF
ON
OFF
LED Status
LINE
OFF
ON
OFF
FF
OFF
ON
OFF
SUPPLY
OFF
ON
OFF
ERROR
HOTHING
ALL BLACK
COLD RESET
(about 4sec)
LCD Status
Power ON
Initialize EEPROM
Check the
Key
7 – 7
Содержание JX-8200
Страница 201: ...14 2 ...
Страница 202: ...14 3 ...
Страница 203: ...14 4 ...
Страница 204: ...14 5 ...