Sea-doo 2004 GTI Скачать руководство пользователя

Страница: 5 / 130

12) Fuel Tank Valve .................................................................................

13) Fuel Tank Cap ...................................................................................

14) Oil Injection Reservoir Cap................................................................

15) Front Storage Compartment Cover...................................................

16) Front Storage Compartment Cover Latch.........................................

17) Tool Kit ..............................................................................................

18) Air Intake Opening ............................................................................

19) Seat Strap .........................................................................................

20) Seat Latch (if so equipped) ...............................................................

21) Seat Extension Latch (if so equipped)...............................................

22) Rear Grab Handle..............................................................................

23) Rear Storage Basket (if so equipped)................................................

24) Bow and Stern Eyelets .....................................................................

25) Mooring Cleats..................................................................................

26) Footboard..........................................................................................

27) Boarding Pads ...................................................................................

28) Boarding Platform .............................................................................

29) Boarding Step (if so equipped)..........................................................

30) Cooling System Bleed Outlet............................................................

31) Flushing Connector (if so equipped) .................................................

32) Bilge Drain Plugs...............................................................................

33) Jet Pump Nozzle ...............................................................................

34) Reverse Gate (if so equipped)...........................................................

35) Jet Pump Water Intake .....................................................................

36) Fuses ................................................................................................

37) Battery ..............................................................................................

38) Side Vanes (if so equipped)...............................................................

39) Rear Access Cover............................................................................

40) Automatic Bilge Pump ......................................................................

LIQUIDS ...................................................................................... 50

Fueling Procedure ...................................................................................

Recommended Fuel ................................................................................

Recommended Oil ..................................................................................

Oil Injection System ................................................................................

BREAK-IN PERIOD ...................................................................... 52

10-Hour Inspection ..................................................................................

PRE-OPERATION CHECKS .......................................................... 53

Hull ..........................................................................................................

Jet Pump Water Intake ...........................................................................

Bilge ........................................................................................................

Water Flow in Cooling System
(only when temperature is below or close to freezing point) ..................

Battery.....................................................................................................

Fuel Tank and Oil Reservoir ......................................................................

smo2004-002a.book Page 3 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

Содержание 2004 GTI



































































































































Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды

Sea-doo 2004 GTI, Руководство оператора

Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды