Sea-doo 2004 GTI Скачать руководство пользователя страница 106

Страница: 106 / 130

106

Engine Lacks Acceleration or Power

Watercraft Engine Cannot Run Above Idle Speed

Watercraft Can Not Reach Top Speed

Abnormal Noise From Propulsion System

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

• Weak spark.

Refer to engine MISFIRES, RUNS
IRREGULARLY.

• Incorrect fuel mixture

(

carburetor-equipped models

Refer to engine MISFIRES, RUNS
IRREGULARLY.

• Water in fuel or injection oil.

Siphon and replace.

Overheated engine.

See engine OVERHEATS.

• Clogged injectors

(RFI and DI models)

Refer to an authorized SEA-DOO
dealer.

• Low fuel pressure

(RFI and DI models)

Refer to an authorized SEA-DOO
dealer.

• Stuck RAVE valves

(

if so equipped

Refer to an authorized SEA-DOO
dealer.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

• The monitoring system put the

watercraft in limp home mode
due to a component malfunc-
tion (

DI models

Try removing and reinstalling the
safety lanyard on its post. Refer
to an authorized SEA-DOO dealer.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Cavitation.

• Jet pump water intake clogged.

Clean.

• Damaged impeller.

Replace. Refer to an authorized
SEA-DOO dealer.

• The safety lanyard used purpose-

ly does not allow watercraft top
speed (

DI models

Use a safety lanyard that allows to
reach the top speed.

• The monitoring system put the

watercraft in limp home mode
due to a component malfunc-
tion (

DI models

Release throttle so that engine
returns to idle speed. Refer to an
authorized SEA-DOO dealer.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Cavitation.

• Weeds or debris jammed around

impeller.

Clean and check for damage.

• Damaged impeller shaft or drive

shaft.

Refer to an authorized SEA-DOO
dealer.

smo2004-002a.book Page 106 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

Содержание 2004 GTI



































































































































Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды

Sea-doo 2004 GTI, Руководство оператора

Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды