Sea-doo 2004 GTI Скачать руководство пользователя | Manualshive

Страница: 62 / 130

background image

61

CA UT ION :

C o m b us ti o n e ng i n e

needs air to operate; consequently
this watercraft cannot be totally wa-
tertight. Any maneuvers such as fig-
ure eights etc., that cause the upper
deck to be under water may cause
severe engine problems due to wa-
ter ingestion. Refer to SPECIAL PRO-
CEDURES and LIMITED WARRAN-
TY contained in this section.

Models with Off-Power Assisted
Steering System (O.P.A.S.)

Two side vanes on the rear sides of the
hull, turn as the steering is turned to
assist the watercraft turning. At first,
carefully experiment turning with this
system.

1. Side vanes turn following steering movement

Boarding the Watercraft

General

As with any watercraft, boarding should
be done carefully and engine should not
be running.

On some models

, boarding is facilitat-

ed by using a step.

Boarding from a Dock or in
Shallow Water

When boarding from a dock, slowly
place one foot on the watercraft foot-
board nearest the dock and, at the
same time, transfer the body weight to
the other side in order to balance the
watercraft while holding the handlebar.
Then, bring the other foot over the seat
and put it on the other footboard. Push
the watercraft away from the dock.

In shallow water, board the watercraft
either from the side or the rear.

Ensure there is at least 90 cm (3 ft) of
water underneath the lowest rear por-
tion of the hull.

Take into account that the hull will lower
in water when all passengers are
aboard. Be certain to maintain the spec-
ified depth so sand, pebbles and rocks
will not be drawn up in the jet pump.



WARNING

Engine should be OFF when board-
ing the watercraft or when using
boarding step (

if so equipped

).

Keep limbs away from jet or intake
grate. Stay on center of the step.
Only one person at a time on the
step. Never use the step for pulling,
towing, diving or jumping, board-
ing a watercraft that is out of water
or any other purpose other than a
boarding step.

1

F17K03Y



WARNING

Inexperienced riders should practice
how to get aboard (all methods ex-
plained here) close to shore first
before venturing into deep water.



WARNING

Never use jet pump components
as a supporting point to board the
watercraft.

F18A01Y

smo2004-002a.book Page 61 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
60
61
62
63
64
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Sun odyssey 509

Бренд: Jeanneau Страницы: 8

Бренд: Jeanneau Страницы: 130

2009 Signature 250

Бренд: Chaparral Страницы: 148

Бренд: React Страницы: 8

Бренд: PROAQUA Страницы: 24

Бренд: YAMARIN Страницы: 25

Бренд: Banzai Страницы: 10

Бренд: Stand Up Floats Страницы: 4

Бренд: Four winns Страницы: 139

Бренд: Sea-doo Страницы: 130

Бренд: Sea-doo Страницы: 14

Бренд: Sea-doo Страницы: 88

Бренд: Baja Страницы: 83

Бренд: J/Boats Страницы: 23

Бренд: Gumotex Страницы: 40

Бренд: Sailfish Страницы: 44

Бренд: Jeanneau Страницы: 150

WaveRunner SuperJet 700 2001

Бренд: Yamaha Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды