Sea-doo 2004 GTI Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 130

background image

91

O.P.A.S. System
(if so equipped)

The O.P.A.S. system operation and
condition should be checked by an au-
thorized SEA-DOO dealer.

General Inspection and
Cleaning

Inspection

Check engine compartment for any dam-
age and fuel/oil injection systems for
leaks. Ensure all hose clamps are proper-
ly secured and no hose is cracked, kinked
or presenting any other damage.

Inspect muffler, battery, fuel tank and
oil reservoir fastening devices. Visually
check electrical connections for corro-
sion and tightness.

Inspect hull and jet pump water intake
grate for damage. Replace or have dam-
aged parts repaired.

Cleaning

The bilge should be cleaned by an au-
thorized SEA-DOO dealer to remove any
fuel/oil/electrolyte deposits and mildew.

Occasionally, wash the body with wa-
ter and soap (only use mild detergent).
Remove any marine organisms from
engine and/or hull. Apply non-abrasive
wax such as silicone wax.

CAUTION:

Never clean fiberglass and

plastic parts with strong detergent,
degreasing agent, paint thinner, ace-
tone, etc.

Stains may be removed from seat and
fiberglass with Knight’s Spray-Nine
from Korkay System Ltd or the equiv-
alent.

Respect the environment by ensuring
fuel, oil or cleaning solutions do not
drain into the waterways.



WARNING

If any gasoline leak and/or odor are
present, do not start the engine.
Have the watercraft serviced by an
authorized SEA-DOO dealer.



WARNING

Periodically verify the seat lock pin
and tighten if needed. Make sure
seat securely latches.

smo2004-002a.book Page 91 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
89
90
91
92
93
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Mackinaw 156 Canoe

Бренд: KL Industries Страницы: 5

Бренд: whaler Страницы: 80

Mirage Inflatables

Бренд: Hobie Страницы: 2

Бренд: Axiom Страницы: 28

Бренд: Grady-White Boats Страницы: 72

Бренд: Grady-White Boats Страницы: 74

Бренд: Grady-White Boats Страницы: 86

Бренд: Grady-White Boats Страницы: 112

Бренд: PROAQUA Страницы: 24

Бренд: Blue Wave Страницы: 22

Бренд: UIM Страницы: 17

Бренд: Sailfish Страницы: 32

Бренд: Zodiac Страницы: 10

Бренд: Yamaha Страницы: 206

GP1300R WaveRunner 2008

Бренд: Yamaha Страницы: 98

Бренд: Williams Страницы: 15

DC 235 DUAL CONSOLE

Бренд: PERSUIT Страницы: 120

Бренд: Lund Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды