Главная
/
Sea-doo
/
2004 GTI
/
Руководство оператора

Sea-doo 2004 GTI, Руководство оператора

Поделиться

103 страниц до
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130

Страница: 118 / 130

background image

118

CALIFORNIA EMISSION CONTROL WARRANTY
STATEMENT FOR MODEL-YEAR 2004 SEA-DOO

®

PERSONAL WATERCRAFT WITH 947 DI ENGINES

Your Sea-Doo personal watercraft has a special environmental label required by the Califor-
nia Air Resources Board. The label has 1, 2, 3 or 4 stars. A hangtag, provided with your
personal watercraft, describes the meaning of the star rating system.

The Star Label means Cleaner Marine Engines

The Symbol for Cleaner Marine Engines:

Cleaner Air and Water

For a healthier lifestyle and environment.

Better Fuel Economy

Burns up to 30 - 40 percent less gas and oil than conventional carbureted two-stroke
engines, saving money and resources.

Longer Emission Warranty

Protects consumer for worry free operation.

One Star - Low-Emission

The one-star label identifies personal watercraft, outboard, sterndrive and inboard engines
that meet the Air Resources Board’s Personal Watercraft and Outboard marine engine
2001 exhaust emission standards. Engines meeting these standards have 75% lower
emissions than conventional carbureted two-stroke engines. These engines are equivalent
to the U.S. EPA’s 2006 standards for marine engines.

Two Stars - Very Low Emission

The two-star label identifies personal watercraft, outboard, sterndrive and inboard engines
that meet the Air Resources Board’s Personal Watercraft and Outboard marine engine
2004 exhaust emission standards. Engines meeting these standards have 20% lower
emissions than One Star - Low-Emission engines.

Three Stars - Ultra Low Emission

The three-star label identifies engines that meet the Air Resources Board’s Personal Wa-
tercraft and Outboard marine engine 2008 exhaust emission standards or the Sterndrive
and Inboard marine engine 2003 exhaust emission standards. Engines meeting these stan-
dards have 65% lower emissions than One Star - Low Emission engines.

Four Stars - Super Ultra Low Emission

The four-star label identifies engines that meet the Air Resources Board’s Sterndrive and
Inboard marine engine 2009 exhaust emission standards. Personal Watercraft and Out-
board marine engines may also comply with these standards. Engines meeting these stan-
dards have 90% lower emissions than One Star - Low Emission engines.

F18L3CQ

smo2004-002a.book Page 118 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
116
117
118
119
120
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Impression i40.1

Бренд: Elan Страницы: 44

Бренд: Bombard Страницы: 188

Бренд: Hydrospace Страницы: 115

Бренд: Hunter Страницы: 200

Бренд: Hunter Страницы: 271

Бренд: Cobalt Digital Inc Страницы: 136

Бренд: Westport Страницы: 11

Бренд: Axopar Страницы: 39

Бренд: Dehler Страницы: 94

Бренд: Seamax Страницы: 34

Бренд: Quicksilver Страницы: 71

Бренд: Laser Страницы: 28

Бренд: Wave Sport Страницы: 12

Бренд: PATHFINDER Страницы: 28

Бренд: Yamaha Страницы: 116

MILPRO HEAVY DUTY Series

Бренд: Zodiac Страницы: 19

Бренд: Sea Ray Страницы: 16

Бренд: Sea Ray Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды