Sea-doo 2004 GTI Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 130

background image

71

CAUTION:

Always refer to decal lo-

cated on stern of watercraft.

To return the watercraft upright, en-
sure the engine is off, grab the inlet
grate, step on bumper rail and use your
weight to rotate the watercraft.

GTI and GTI LE Models

Rotate the watercraft

clockwise

(seen

from rear).

GTI RFI and GTI LE RFI Models

Rotate the watercraft

counterclock-

wise

(seen from rear).

Submerged Watercraft

To limit damages to the engine, per-
form the following procedure as soon
as possible.

Drain bilge.

If it was submerged in

salt water

, spray

bilge and all components with fresh wa-
ter using a garden hose to stop the salt
corroding effect.

CAUTION:

Never try to crank or start

the engine. Water trapped in engine
may cause severe damage to the en-
gine components.

Bring the watercraft to be serviced by
an authorized Sea-Doo dealer as soon
as possible.

CAUTION:

The longer the delay be-

fore you have the engine serviced,
the greater the damage will be to the
engine.

Water-Flooded Engine

In the event the engine cannot be ser-
viced within a few hours, remove spark
plug cables and connect them on the
grounding device.

Remove spark plugs and dry them with
a clean and dry cloth.

Cover spark plug holes with a rag.

Carburetor-Equipped Models

Ensure choke lever is completely pushed
in.

Fully depress the throttle lever and hold.

RFI Models

To prevent fuel to be injected in the en-
gine, proceed as follows.

Remove safety lanyard from its post.

Depress and hold the throttle lever at
full throttle position. Wait 2 seconds
then, reinstall the safety lanyard cap
while keeping throttle lever fully de-
pressed.



WARNING

When watercraft is capsized, do
not attempt to restart the engine.
Operator and passengers should
always wear approved personal
flotation devices.

F00A24Y

F00A25Y



WARNING

Never crank engine with spark
plugs removed unless spark plug
cables are connected to the ground-
ing device. Be careful when crank-
ing engine, water will spray out
from spark plug holes.

smo2004-002a.book Page 71 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
70
71
72
73
74
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Бренд: Lakemaster Страницы: 14

AIRFUSION EVO AE1042

Бренд: Advanced Elements Страницы: 50

Бренд: 3D Tender Страницы: 18

R-29 Command Bridge

Бренд: Ranger Tugs Страницы: 21

Бренд: Boston Whaler Страницы: 44

SEASCOOTER SD5542

Бренд: Sea-doo Страницы: 16

Бренд: Nauticstar Страницы: 82

Бренд: World Cat Страницы: 38

Бренд: World Cat Страницы: 68

Бренд: SeaDoo Страницы: 801

Бренд: BENETEAU Страницы: 238

Бренд: Ockelbo Страницы: 70

Бренд: Vanguard Страницы: 6

sun odyssey 54 DS

Бренд: Jeanneau Страницы: 115

Бренд: BearCreeks Страницы: 17

WaveRunner VX Deluxe 2007

Бренд: Yamaha Страницы: 96

Бренд: Wayland Folding Kayaks Страницы: 9

Wildflower J/35c

Бренд: SEATTLE Sailing Club Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды