Sea-doo 2004 GTI Скачать руководство пользователя | Manualshive

Страница: 42 / 130

background image

41

12) Fuel Tank Valve

Carburetor-Equipped Models

1. ON
2. OFF

A 3-position rotating valve: OFF, ON and
RESERVE:

OFF: Stop fuel supply to carburetor(s).

CAUTION:

Turn valve to OFF posi-

tion when

watercraft

is not operated.

ON: Allows fuel to flow to carbure-

tor(s). This is the normal position
for operation of watercraft.

CAUTION:

Improper opening of fuel

valve may restrict flow of fuel and
may lead to engine damage. Make
sure valve is fully opened while run-
ning.

RES (RESERVE): Use when the water-

craft has run out of fuel in the ON
position.

Always refill the fuel tank at the first
opportunity. After refueling, turn the
fuel tank valve to the ON position to
continue operation.

13) Fuel Tank Cap

Some Models

Open the front storage compartment
cover to expose fuel tank cap.

All Models

Refer to the vehicle illustration for fuel
tank cap location.

Unscrew the cap counterclockwise. Af-
ter fueling, reinstall cap and fully tighten.

14) Oil Injection Reservoir

Cap

All Models except XP DI

Refer to the vehicle illustration for oil
injection reservoir cap location.

Open the front storage compartment
cover to expose reservoir cap.

To add injection oil in the reservoir, un-
screw the cap counterclockwise. Do
not overfill. Reinstall cap and fully tight-
en it.

Close and latch storage compartment
cover.

1

F17L0DY

2



WARNING

Always stop the engine before re-
fueling. Fuel is flammable and ex-
plosive under certain conditions.
Always work in a well ventilated
area. Do not smoke or allow open
flames or sparks in the vicinity.
Fuel tank may be pressurized, turn
cap slowly when opening.

Never

use an open flame to check fuel
level. When fueling, keep water-
craft level. Do not overfill or top off
the fuel tank and leave watercraft
in the sun. As temperature in-
creases, fuel expands and might
overflow. Always wipe off any fuel
spillage from the watercraft. Peri-
odically verify fuel system. Al-
ways turn the fuel tank valve

(if so

equipped)

to OFF position when

the watercraft is not in use.



WARNING

Do not overfill. Reinstall cap and
fully tighten. Oil is flammable. Al-
ways wipe off any oil spillage
from the bilge.

smo2004-002a.book Page 41 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
40
41
42
43
44
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Бренд: FARRIER MARINE Страницы: 52

Бренд: Edgewater Networks Страницы: 39

Бренд: RTM Страницы: 26

AIRFUSION EVO AE1042

Бренд: Advanced Elements Страницы: 50

NeedleNose SUP NN116

Бренд: Sea Eagle Страницы: 13

Бренд: Scout Boats Страницы: 116

Бренд: Hobie Страницы: 26

Бренд: Nauticstar Страницы: 80

Бренд: Jeanneau Страницы: 104

Бренд: Camper & Nicholson Страницы: 22

Бренд: Banzai Страницы: 10

Бренд: BRIG Страницы: 38

VX WaveRunner 2007

Бренд: Yamaha Страницы: 108

Бренд: Kayak Innovations Страницы: 2

Бренд: Malibu Boats Страницы: 176

Бренд: NorthStar Страницы: 2

190 Outrage 2019

Бренд: Boston Whaler Страницы: 88

Бренд: BENETEAU Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды