Sea-doo 2004 GTI Скачать руководство пользователя

Страница: 102 / 130

102

Preseason Preparation Chart

NOTE:

It is highly recommended that an authorized SEA-DOO dealer perform the

annual safety inspection and factory campaigns in addition to the preseason prep-
aration all at the same time.

➀

Before installing new spark plugs, it is suggested to burn the excess BOMBARDIER

LUBE lubricant or equivalent by starting the engine using the old spark plugs.

➁

Safety item covered in the annual safety inspection.

OPERATIONS

TO BE

PERFORMED

GENERAL

Lubrication/corrosion protection

Operator

Spark plug replacement

➀

Dealer

ENGINE

Exhaust system condition (fasteners, hoses etc.)

Dealer

RAVE valve cleaning (

if so equipped

)

Dealer

Counterbalance shaft oil level (

if so equipped

)

Dealer

TDC setting (

RFI and DI models

)

Dealer

Air compressor, visual condition of hoses. Check for leaks
(

DI models

)

CAUTION:

Main hose between compressor and fuel rail may be

hot.

Dealer

COOLING SYSTEM

Inspection of cooling system hoses and components

Dealer

FUEL SYSTEM

Carburetor adjustment (

carburetor-equipped models

)

Dealer

Throttle

➁

and choke (

carburetor-equipped models

)

cable

inspection/adjustment

Dealer

Fuel filter replacement (

except RFI models

)

Dealer

Fuel injection sensors verification (

RFI and DI models

)

Dealer

Fuel system; check valves, lines, fasteners,

pressurization

➁

Dealer

Direct injector, check for leakage (

DI models

) Dealer

Filler neck, fuel tank and fuel cap condition

➁

Dealer

Flame arrester inspection (

DI models

)

➁

Dealer

Fuel tank straps

Operator

Refill fuel tank

Operator

LUBRICATION
SYSTEM

Oil injection pump adjustment and bleeding

Dealer

Oil filter replacement

Dealer

Oil injection reservoir straps

Operator

Oil injection reservoir filling

Operator

ELECTRICAL
SYSTEM

Battery condition/charging and reinstallation

Dealer

Battery, starter connections and routing

➁

Dealer

Monitoring beeper

Dealer

Digitally encoded security system

Dealer

STEERING SYSTEM

Steering system adjustment/inspection

➁

Dealer

O.P.A.S. SYSTEM

(if so equipped)

Check O.P.A.S. system condition.

Dealer

PROPULSION
SYSTEM

Shifter system condition and cable adjustment

Dealer

VTS (Variable Trim System,

if so equipped

)

Dealer

Propulsion system inspection

Dealer

Jet pump oil replacement

Dealer

HULL AND BODY

Inspection of bailer pick-ups

Dealer

smo2004-002a.book Page 102 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

Содержание 2004 GTI



































































































































Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды

Sea-doo 2004 GTI, Руководство оператора

Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды