Sea-doo 2004 GTI Скачать руководство пользователя | Manualshive

Страница: 74 / 130

background image

73

DI Models

To prevent fuel to be injected and also
to cut the ignition at the engine start-
ing, proceed as follows.

While engine is stopped, fully depress
throttle lever and HOLD for cranking.

Crank engine approximately 5 sec-
onds.

NOTE:

A 1 second beep every second

indicates the drowned mode is active.

Release throttle lever and crank en-
gine.

All Models

If it does not work:

Remove spark plug cables and connect
them on the grounding device.

Remove spark plugs and dry them using
a rag.
Cover spark plug holes with a rag.
Crank engine several times.
Reinstall spark plugs. Install clean dry
spark plugs if possible. Reconnect ca-
bles.

DI Models

1. MAG side spark plug cable

All Models

Start engine as explained above. If en-
gine continues to flood, see an autho-
rized SEA-DOO dealer.

Out of Fuel

DI Models

When running the engine out of fuel,
it may be necessary to remove and in-
stall the safety lanyard 2 - 3 times to
initially feed the fuel system after fuel
tank refill.

Towing the

Watercraft

in

Water

All Models

Special precautions should be taken
when towing a SEA-DOO watercraft in
water.

Maximum recommended towing speed
is 24 km/h (15 MPH).

When towing your watercraft in water,
pinch the water supply hose from the
impeller housing to the engine with a
large hose pincher (P/N 529 032 500).



WARNING

Always use spark plug cable ground-
ing device when removing spark
plugs. Never crank engine with
spark plugs removed unless spark
plug cables are connected to the
grounding device.



WARNING

Always reconnect spark plug ca-
bles at the same spark plugs where
they come from. The cable coming
out the edge of the electrical box
must be connected to the MAG side
spark plug.

F17L19Y

1

smo2004-002a.book Page 73 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
72
73
74
75
76
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Бренд: SEATTLE Sailing Club Страницы: 9

260 Canyon Runner

Бренд: Glacier bay Страницы: 50

Бренд: Malibu Boats Страницы: 202

Бренд: ABSTRACT Страницы: 10

Бренд: Hunter Страницы: 7

Бренд: Polaris Страницы: 90

CAP CAMARAT 6.5 WA

Бренд: Jeanneau Страницы: 96

WaveRunner VXS 2015

Бренд: Yamaha Страницы: 108

Бренд: Hunter Страницы: 186

Бренд: CORRECT CRAFT Страницы: 84

Бренд: Silver Страницы: 134

Бренд: Phileas Страницы: 24

Бренд: MasterCraft Страницы: 76

Бренд: MasterCraft Страницы: 285

Бренд: MasterCraft Страницы: 41

1991 Barefoot 200

Бренд: MasterCraft Страницы: 52

Бренд: MasterCraft Страницы: 66

1994 ProSport 205

Бренд: MasterCraft Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды