Sea-doo 2004 GTI Скачать руководство пользователя

Страница: 63 / 130

CAUTION:

Starting the engine or

riding the watercraft in shallower
water might damage the impeller or
other jet pump components.

A. Maintain at least 90 cm (3 ft) underneath the

lowest rear portion of the hull when all
passengers are aboard

Boarding in Deep Water

Operator Alone

Swim to the rear of the watercraft.

Grip the grab handle and pull yourself
upward until your knee can reach the
boarding platform then grip the seat
strap.

Bring your feet on the footboard while
maintaining balance using the handle-
bar

(except 3-up seat models)

Sit astride the seat.

Operator with a Passenger

The operator climbs on the watercraft
the same way as explained previously.

In choppy water, the passenger, while
in the water, may hold the watercraft
to help the operator in climbing aboard.

The passenger then climbs on the wa-
tercraft while the operator maintains
balance by sitting as close as possible
to the console.

F18L0XY

F01L5JY

F01L4JY

F01L4KY

F01L4MY

F01L4NY

smo2004-002a.book Page 62 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

Содержание 2004 GTI



































































































































Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды

Sea-doo 2004 GTI, Руководство оператора

Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды