Sea-doo 2004 GTI Скачать руководство пользователя

Страница: 105 / 130

105

Engine Misfires, Runs Irregularly

Engine Overheats

Engine Continually Backfires

Engine Pinging or Knocking

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Weak spark.

• Fouled/defective/worn spark

plugs.

Replace.

• Faulty MPEM.

Refer to an authorized SEA-DOO
dealer.

• Too much oil supplied to engine.

Improper oil pump adjustment,
refer to an authorized SEA-DOO
dealer.

Lean fuel mixture.

• Fuel: Level too low, stale or water-

contaminated.

Siphon and/or refill.

• Fuel filter, clogged or water-

contaminated
(

carburetor-equipped models

Refer to an authorized SEA-DOO
dealer.

• Fuel tank valve

(

carburetor-equipped models

)

partially open.

Turn fuel tank valve to ON position.

• Clogged injectors

(

RFI and DI models

Refer to an authorized SEA-DOO
dealer.

• Defective sensor or MPEM

(

RFI and DI models

Refer to an authorized SEA-DOO
dealer.

Rich fuel mixture
(high fuel consumption).

• Flame arrester dirty/clogged

(

if so equipped

Clean or replace.

• Partially closed choke

(

carburetor-equipped models

Refer to an authorized SEA-DOO
dealer.

• Defective sensor or MPEM

(

RFI and DI models

Refer to an authorized SEA-DOO
dealer.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Monitoring beeper
sounds continuously.

• Clogged jet pump water intake.

Clean.

• Clogged coolant system.

Flush cooling system.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Weak spark.

• Fouled/defective/worn spark

plugs.

Replace.

Overheated engine.

• See engine OVERHEATS.

Refer to an authorized SEA-DOO
dealer.

• Faulty rev limiter in MPEM

(

carburetor-equipped models

Refer to an authorized SEA-DOO
dealer.

• Spark plug leads or wiring re-

versed.

Connect spark plug cables at their
proper location. Otherwise, refer
to an authorized SEA-DOO dealer.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

• Poor quality gasoline/low octane.

Use well known quality and rec-
ommended gasoline.

• Spark plug heat range too high.

Use recommended spark plugs.

• Ignition timing or TDC setting.

Refer to an authorized SEA-DOO
dealer.

smo2004-002a.book Page 105 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

Содержание 2004 GTI



































































































































Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды

Sea-doo 2004 GTI, Руководство оператора

Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды