Sea-doo 2004 GTI Скачать руководство пользователя | Manualshive

Страница: 73 / 130

background image

72

DI Models

To prevent fuel to be injected and also
to cut the ignition at the engine start-
ing, proceed as follows.

While engine is stopped, fully depress
throttle lever and HOLD for cranking.

NOTE:

A 1 second beep every second

indicates the drowned mode is active.

All Models

Crank engine several times to allow wa-
ter to escape from spark plug openings.

Release throttle lever.

DI Models

If water does not completely go out, it
may be necessary to remove the air in-
take silencer then to lean the vehicle so
that water can flow out from throttle
bodies.

All Models

Spray BOMBARDIER LUBE lubricant
or equivalent into spark plug holes.

Crank engine again.

Reinstall spark plugs. Install clean dry
spark plugs if possible. Reconnect ca-
bles.

1. MAG side spark plug cable

Start engine normally.

Fuel-Flooded Engine

When the engine does not start after
several attempts, the engine may be
fuel-flooded. Proceed as follows.

Carburetor-Equipped Models

Install the safety lanyard cap on its post.
Ensure choke lever is completely pushed
in.
Fully depress the throttle lever and hold
while starting the engine. Try several
times.

Crank the engine a few turns to distrib-
ute the oil on cylinder wall.

RFI Models

To prevent fuel to be injected in the en-
gine, proceed as follows.

Remove safety lanyard from its post.

Depress and hold the throttle lever at
full throttle position. Wait 2 seconds
then, reinstall the safety lanyard cap
while keeping throttle lever fully de-
pressed.

Crank engine approximately 5 sec-
onds.

Release throttle lever and crank en-
gine.



WARNING

Always reconnect spark plug ca-
bles at the same spark plugs where
they come from. The cable coming
out the edge of the electrical box
must be connected to the MAG side
spark plug.

F17L19Y

1

smo2004-002a.book Page 72 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
71
72
73
74
75
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Бренд: Malibu Kayaks Страницы: 2

Бренд: Malibu Kayaks Страницы: 3

Бренд: Jeanneau Страницы: 100

45 COCKPIT MOTOR

Бренд: Carver Страницы: 141

Бренд: Ockelbo Страницы: 64

Бренд: Sailfish Страницы: 41

475 New Age 2015

Бренд: Corsiva Yachting Страницы: 38

Бренд: Sea-doo Страницы: 116

SAR 2018 Series

Бренд: Sea-doo Страницы: 164

Alice Bavaria Cruiser 51 2016

Бренд: Hermes Yachting Страницы: 25

Бренд: X-TREME scooter Страницы: 30

Бренд: Kingfisher Страницы: 35

CRUSER 51 KONDOR 2018

Бренд: Bavaria Страницы: 30

Бренд: buster Страницы: 203

Бренд: Gumotex Страницы: 40

LEADER 33 OUTBOARD

Бренд: Jeanneau Страницы: 198

MERRY FISHER 725 HB

Бренд: Jeanneau Страницы: 102

XLT800 WaveRunner 2004

Бренд: Yamaha Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды