Sea-doo 2004 GTI Скачать руководство пользователя | Manualshive

Страница: 69 / 130

background image

68

GTI AND GTI LE MODELS

1. Grounding device

GTI RFI AND GTI LE RFI MODELS

1. Grounding device

Remove both spark plugs and spray
BOMBARDIER LUBE lubricant or equiv-
alent into each cylinder.

Carburetor-Equipped Models

Crank the engine a few turns to distrib-
ute the oil on cylinder wall.

RFI Models

Remove safety lanyard from its post.

Depress the throttle lever at full throt-
tle position and hold.

Reinstall the safety lanyard cap on its
post.

Crank the engine a few turns to distrib-
ute the oil on cylinder wall.

NOTE:

Proceeding in this order, no

fuel will be injected into the engine.

DI Models

To prevent fuel to be injected and also
to cut the ignition at the engine start-
ing, proceed as follows.

While engine is stopped, fully depress
throttle lever and HOLD for cranking.

NOTE:

A 1 second beep every second

indicates the drowned mode is active.

Crank the engine a few turns to distrib-
ute the oil on cylinder wall.

All Models

Apply anti-seize lubricant on spark plug
threads then reinstall them.

Properly reconnect spark plug cables
to spark plugs.

1. MAG side spark plug cable

Wipe up any residual water from the
engine.

717 and 787 RFI Engines

Reinstall plug on air intake silencer cover.

Anticorrosion Treatment

To prevent corrosion, spray a corrosion
inhibitor (salt water resistant) such as
BOMBARDIER LUBE lubricant or equiv-
alent over metallic components in en-
gine compartment.

Apply dielectric grease (salt water re-
sistant) on battery posts and cable con-
nectors.

CAUTION:

Never leave rags or tools in

the engine compartment or in the bilge.

F01H7CY

1

1

F01H7DY



WARNING

On

DI models

always reconnect

spark plug cables at the same spark
plugs where they come from. The
cable coming out the edge of the
electrical box must be connected to
the MAG side spark plug.

F17L19Y

1

smo2004-002a.book Page 68 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
67
68
69
70
71
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Бренд: Kadey-Krogen Yachts Страницы: 449

Бренд: Anacortes Yacht Charters Страницы: 22

Genesis Console 310

Бренд: Walker Bay Страницы: 12

Бренд: Hobie Страницы: 17

Бренд: Fish Cat Страницы: 8

Бренд: Coastal Страницы: 16

Бренд: Johnson Outdoors Страницы: 12

Бренд: NW Explorations Страницы: 64

Бренд: NW Explorations Страницы: 68

Бренд: J/Boats Страницы: 66

Бренд: Sailfish Страницы: 54

190 Outrage 2019

Бренд: Boston Whaler Страницы: 88

Бренд: J/Boats Страницы: 54

400 Sedan bridge

Бренд: Sea Ray's Страницы: 42

Бренд: Per Brohall Страницы: 34

Бренд: Chris-Craft Страницы: 189

Бренд: HISON Страницы: 40

Бренд: Northern Diver Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды