Sea-doo 2004 GTI Скачать руководство пользователя

Страница: 104 / 130

104

Engine Will Not Start

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Engine does not turn over.

• Safety lanyard removed.

Install cap over post.

• Burnt fuse on MPEM or in elec-

trical box: battery, starting sys-
tem, fuel pump (

DI models

Check wiring then replace fuse(s).

• Discharged battery.

Refer to an authorized SEA-DOO
dealer.

• Battery connections, corroded

or loose.

Refer to an authorized SEA-DOO
dealer.

• Water-flooded engine.

Refer to WATER-FLOODED EN-
GINE in SPECIAL PROCEDURES.

• Faulty sensor

(

RFI and DI models

) or MPEM.

Refer to an authorized SEA-DOO
dealer.

• Seized engine.

Refer to an authorized SEA-DOO
dealer.

• Seized jet pump.

Try to clean. Otherwise, refer to
an authorized SEA-DOO dealer.

Engine turns slowly.

• Loose battery cable connections. Check/clean/tighten.

• Discharged or weak battery.

Refer to an authorized SEA-DOO
dealer.

• Worn starter.

Refer to an authorized SEA-DOO
dealer.

Engine turns normally.

• Closed fuel tank valve

(

carburetor-equipped models

Turn fuel tank valve to ON posi-
tion.

• Fuel tank empty or water-

contaminated.

Refill. Siphon and fill with fresh fu-
el.

• Fuel filter clogged or water-

contaminated
(

carburetor-equipped models

Clean, check fuel tank for water.

• Fouled/defective spark plugs.

Replace.

• Misuse of choke

(

carburetor-equipped models

Use only with cold engine. Re-
place spark plugs.

• Fuel-flooded engine.

Refer to FUEL-FLOODED EN-
GINE in SPECIAL PROCEDURES.

• Faulty component in the fuel in-

jection system
(

RFI and DI models

Refer to an authorized SEA-DOO
dealer.

• Burnt fuel pump fuse

(

RFI and DI models

Check wiring then replace fuse.

• Electrical problem

(

RFI and DI models

Refer to an authorized SEA-DOO
dealer.

smo2004-002a.book Page 104 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

Содержание 2004 GTI



































































































































Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды

Sea-doo 2004 GTI, Руководство оператора

Результаты поиска

Содержание 2004 GTI

Отзывы:

Похожие инструкции для 2004 GTI

Бренды по названию

Популярные бренды