Sea-doo 2004 GTI Скачать руководство пользователя | Manualshive

Страница: 56 / 130

background image

55

– Ensure to drain bilge if water is present.

Battery

Fuel Tank and Oil Reservoir

With the watercraft horizontal, fill the
fuel tank to specified level.

Check the oil level and refill reservoir
as necessary.

Check fuel tank and oil reservoir retain-
ing straps/fasteners.

Engine Compartment

Steering System

Assisted by another person, check
steering operation for free movement.
When the handlebar is horizontal, the
jet pump nozzle should be in the straight
ahead position. The rear edge of side
vanes (

if so equipped

) should be

pointing outside of watercraft by ap-
proximately 20°. Ensure the jet pump
nozzle and side vanes (

if so equipped

)

pivot easily and in the same direction
as the handlebar.

Throttle System

Check throttle lever for free and smooth
operation. It should return to its initial
position immediately after it is released.

All Models except RFI and DI

CAUTION:

Engine can be flooded if

throttle lever is applied several times
when engine is not running. If en-
gine is flooded, it will not start.

Shifter System
(if so equipped)

Check reverse gate operation for free
movement. With shift lever in forward
position, the gate should be in upward
position and offering a resistance to go
downward. With the shift lever in neutral
position, gate should be in middle posi-
tion. With shift lever in reverse position,
gate should be in downward position.

VTS (Variable Trim System)
(if so equipped)

Push on arrows on VTS button to check
nozzle movement.



WARNING

Do not use any electrical heating
device to heat the cooling system.
Electrical devices may generate
sparks that would ignite fuel va-
pors that might be present in the
bilge causing a fire or an explosion.



WARNING

Verify tightness of battery cables to
their posts and condition of battery
retaining strap(s)/fasteners. Do not
charge or boost battery while in-
stalled.



WARNING

Should any leak or gasoline odor
be present, do not start the engine.
Refer to an authorized SEA-DOO
dealer before use.



WARNING

Check handlebar and correspond-
ing steering nozzle operation be-
fore starting. Never turn handle-
bar while someone is nearby rear
of watercraft. Keep away from
steering moving parts (nozzle, side
vanes, linkage etc.).



WARNING

Check throttle lever operation be-
fore starting the engine.



WARNING

Verify the reverse gate operation
before starting the engine.

smo2004-002a.book Page 55 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
54
55
56
57
58
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Бренд: Rave Sports Страницы: 16

1992 270 Weekender

Бренд: Sea Ray Страницы: 21

Бренд: Bestway Страницы: 24

Бренд: NorthStar Страницы: 2

Бренд: Hobie Страницы: 15

Бренд: YAMARIN Страницы: 40

Бренд: Corsiva Yachting Страницы: 36

Бренд: Ranger boats Страницы: 36

Бренд: Zoik Страницы: 4

Бренд: Grady-White Boats Страницы: 74

Бренд: Bavaria Страницы: 26

Бренд: Bavaria Страницы: 28

Бренд: Polaris Страницы: 114

Бренд: Walker Bay Страницы: 4

Бренд: Jeanneau Страницы: 100

Бренд: NorthStar Страницы: 2

Sun Marine Frp-330

Бренд: boAt Страницы: 3

K-Light Classic 2008

Бренд: Feathercraft Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды