Sea-doo 2004 GTI Скачать руководство пользователя | Manualshive

Страница: 55 / 130

background image

54

Hull

Inspect hull for cracks or damage.

Jet Pump Water Intake

Remove weeds, shells, debris or any-
thing else that could restrict the flow
of water and damage cooling system
or propulsion unit. Clean as necessary.
If any obstruction can not be removed,
refer to an authorized SEA-DOO dealer
for servicing.

TYPICAL

1. Water intake
2. Ride plate

Inspect leading edges of the impeller,
if they have nicks or bends performance
will be greatly reduced.

Bilge

Should water be present in the bilge,
tilt the watercraft to the rear and un-
screw drain plugs to completely empty
the bilge.

Secure bilge drain plugs.

Water Flow in Cooling
System (only when
temperature is below or
close to freezing point)

In Northern areas, if watercraft is to be
used when temperature is below or
close to freezing point (0°C (32°F)) or if
watercraft was left unused while tem-
perature was below or close to freez-
ing point, water may be frozen in cool-
ing system hoses. This could cause
cooling system overheating. To ensure
it is properly working, do the following

prior to using the watercraft

:

– The procedure is to be performed

with watercraft out of water.

– Connect a garden hose to the flush-

ing connector at jet pump.

– Perform the flushing operation as ex-

plained in POST-OPERATION CARE.

– Ensure water flows out

of jet pump

.

Otherwise, water is frozen in cooling
system and restricts water flow.

Do

not operate the watercraft in this
condition

.

NOTE:

Pay attention that some water

will also flow out of exhaust outlet.
Make sure water is effectively

flowing

out of jet pump

.

CAUTION:

Operating watercraft with

frozen water in cooling system might
lead to engine components damage.

NOTE:

When water freezes, damage

to engine components should not oc-
cur because of water expansion, but
because it prevents full flow of cooling
water.

– Either wait until ice melts or pour

some hot water to cooling system
components and to engine. Then,
perform the flushing operation again
to make sure water properly flows
out of jet pump. If you need assis-
tance, refer to an authorized Sea-Doo
dealer.



WARNING

Make sure drain plugs are proper-
ly secured prior to launching the
watercraft in water.

F18J04Y

2

1

smo2004-002a.book Page 54 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
53
54
55
56
57
...
»

Содержание 2004 GTI



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2004 GTI

Бренд: TALAMEX Страницы: 55

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 84

SX230 High output

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 113

Бренд: Yamaha Страницы: 128

SUV1200 WaveRunner 2004

Бренд: Yamaha Страницы: 140

SUV1200 WaveRunner 2003

Бренд: Yamaha Страницы: 140

GP800R WaveRunner 2003

Бренд: Yamaha Страницы: 124

FX Cruiser WaveRunner 2007

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 121

GP1300R WaveRunner 2003

Бренд: Yamaha Страницы: 126

GP1200R WaveRunner 2001

Бренд: Yamaha Страницы: 126

FX Cruiser SHO WaveRunner 2013

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды