Screen Print & Inkjet Fast T-Jet Blazer Pro Скачать руководство пользователя страница 23

Страница: 23 / 138

Casters have been built into the cabinet base, allowing for easy movement to

a suitable location within your shop. When determining where to set up your

printer, keep in mind the Fast T-Jet Blazer Pro requires an area of at least 12 ft x

10 ft (3.6 m x 3.6 m) for the printer and workspace around it. Additional space is

required for drying, pretreating garments, garment staging, etc.

Note:

Remove any obstacles. All doorways and corridors the printer will travel

through must be at least 36 inches (92 cm) wide.

When the Blazer Pro reaches its final destination,

manually lower the ground supports on all

four corners. Using a box level (found at any

hardware store), check the Print Bed to ensure it

and the machine are level. Each ground support

is threaded and can be raised or lowered to

make any needed height adjustments. Once

you have leveled the machine, tighten each

locking nut against the bottom of the cabinet

base.

Installing the User Interface

The User Interface (UI) controls basic printer operation

and is touch sensitive. To install the UI you will need a

5mm Allen wrench

Unpack the User Interface and locate the (2) 5mm hex

screws for installation.

Position the extension bracket along the back of the machine as shown below.

Using the Allen wrench, secure the extension bracket to the printer base.

Connect the UI Serial Port Cable to the cabinet base.

Locking Nut

Ground Support

Chapter 2- Unpacking and Setup

Содержание Fast T-Jet Blazer Pro











































































































































Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды

Screen Print & Inkjet Fast T-Jet Blazer Pro, Руководство пользователя

Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды