Screen Print & Inkjet Fast T-Jet Blazer Pro Скачать руководство пользователя страница 75

Страница: 75 / 138

Kill Switch

As a precaution, your Fast T-Jet Blazer Pro is equipped with a

Kill Switch

in both

the

Home

and

Index

positions. These circuit breakers will only be activated if the

Printer Assembly attempts to exceed specific printing dimensions. These switches

also prevent damage to your machine should the Assembly fail to trip specific

sensors.

In the event you experience a sudden and total loss of power to all systems,

including the User Interface, it may be due to a

Kill Switch

activation. To reset

your system please do the following:

Turn OFF power to your machine by flipping the breaker switch located

next to the AC power cord. If you do not turn OFF the breaker, the Printer

Assembly may immediately activate the

Kill Switch

again after reset.

Move the Printer Assembly 3-4” toward the center of the Platen.

Reboot your system and power ON your printer.

Should you experience a Kill Switch activation, all spooled files and

print jobs must be reloaded and again sent to Print.

Production Rates and Ink Costs

A Production and Cost matrix is available at

www.screenprinters.net

> Support >

Blazer Pro > Downloads.

Chapter 6- Printing with the Fast T-Jet Blazer

Pro

Содержание Fast T-Jet Blazer Pro











































































































































Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды

Screen Print & Inkjet Fast T-Jet Blazer Pro, Руководство пользователя

Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды