Screen Print & Inkjet Fast T-Jet Blazer Pro Скачать руководство пользователя страница 35

Страница: 35 / 138

Windows Vista Users must have Administrator authority to download

and install any drivers. Additionally, you MUST download the

applicable 32 bit OR 64 bit driver based on your

Operating System

NOT your processor. These drivers are NOT interchangeable.

The Fast T-Jet Blazer Pro is a highly modified version of the Epson 4800 with

hundreds of additional parts not provided by Epson. As a result, the Fast T-Jet

Blazer Pro and any driver software is NOT supported by Epson. All support for the

Epson driver and internal Epson components will come from U.S. Screen.

If you have any concerns installing the driver, contact our Support Department

and they will gladly walk you through the process.

Chapter 3- Interacting with Your Printer

Содержание Fast T-Jet Blazer Pro











































































































































Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды

Screen Print & Inkjet Fast T-Jet Blazer Pro, Руководство пользователя

Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды