Screen Print & Inkjet Fast T-Jet Blazer Pro Скачать руководство пользователя страница 123

Страница: 123 / 138

Support Policy

Support for

Fast T-Jet Blazer Pro

is free. Since the machine is designed to be

intuitive and very easy to use, most support questions have to do with using

FastARTIST, FastRIP or printing from specific graphics applications.

For the quickest support, Email your question to

[email protected]

. Be very

specific and include your serial number.

If you purchased the printer from a dealer in the USA, you DO NOT

have to go back to the dealer for support. Simply call or E-mail our

support center. If you purchased the printer from a dealer outside

the USA, you will need to contact your dealer for support.

Support Hours

Toll Free

+1 888-MYTJETS (698-5387)

Technical Support

+1 480-929-2937

Corporate Office

+1 480-929-0640

Fax

+1 480-929-0766

E-mail:

[email protected]

Internet:

www.screenprinters.net

. Click on the

Support

tab.

Support hours:

7:00am to 8:00pm Monday through Friday

9:00am to 3:00pm Saturday and Sunday

(Mountain Standard Time) USA

24 hr. Emergency Support is available

Note:

Arizona does not observe “Daylight Savings Time.”

In the summer months, Arizona is on the same time as California.

Phone Support

We have an excellent staff of Support Specialists who will gladly walk you

through many of the procedures. When calling for support, please have your

serial number handy and be prepared to give a detailed explanation of the

problem. If you have received an error message, please include the error

109

Chapter 12

Product Support

Содержание Fast T-Jet Blazer Pro











































































































































Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды

Screen Print & Inkjet Fast T-Jet Blazer Pro, Руководство пользователя

Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды