Screen Print & Inkjet Fast T-Jet Blazer Pro Скачать руководство пользователя страница 40

Страница: 40 / 138

Perform a Nozzle Check

You must print a

Nozzle Check

to ensure the Print

Head is performing properly. You may use either

paper or film for this test, but we recommend film such

as FastPOSITIVE, available from U.S. Screen. Otherwise

it’s difficult to see White ink on White paper. To initiate

Nozzle Check

Take the printer from

Print

to “Ready (Sheet)” status by pressing the LEFT

arrow button twice. The LCD display will read “Ready” and you will see a

“sheet of paper” icon. Only when in “Ready (Sheet)” status can the Printer

Assembly be moved.

Using the “RIGHT hand” button, shuffle through the UI screens until you get to

the

Mode

Select

screen. Ensure the virtual dial is set to

Manual

Press the “RIGHT hand” button on the UI again until you reach the

Manual

Mechanism

Movement

Utility

(MMMU) screen.

Place your sheet of film or paper on the

first

Shirtboard. The first position is

furthest from the UI and power cables. Take care to align the film or paper

with the Shirtboard’s lower right hand corner (as you face the front of the

printer.)
Under the heading

Position

, press the

Index

button. This will advance the

Printer Assembly to the beginning of the Platen. Using the

Rev

button, position

the Printer Assembly over the medium onto which you will print the

Nozzle

Check

You must now change the printer mode to “Ready (Roll).” Press the LEFT

arrow button on the LCD Control Panel twice. The display will read “Ready”

with a “roll of paper” icon.
On Control Panel, press the RIGHT arrow once and the display will read

“Printer Setup.” Press the DOWN arrow once to see “Test Print.”
Press the RIGHT arrow button once to see “Nozzle Check.” Press the RIGHT

arrow again and “Print” will appear in the display.
To execute the Nozzle Check, press the RIGHT arrow button once.

If the

•

Nozzle Check

does not print correctly, perform a regular Head

Cleaning. This is done by holding down the RIGHT arrow button for 3

seconds. After the Head Cleaning has been completed, execute another

Nozzle Check

Fast T-Jet Blazer Pro User’s Manual

Содержание Fast T-Jet Blazer Pro











































































































































Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды

Screen Print & Inkjet Fast T-Jet Blazer Pro, Руководство пользователя

Результаты поиска

Содержание Fast T-Jet Blazer Pro

Отзывы:

Похожие инструкции для Fast T-Jet Blazer Pro

Бренды по названию

Популярные бренды