Scout MT-700 ENT Скачать руководство пользователя страница 24

Страница: 24 / 155

МТ-700 fleet tracking system

If white list phone numbers were not locally filled, the terminal configuration can be

done only through SCOUT Tech Support.



Tracker mounting

The terminal should not be mounted in direct sunlight or near heaters.

The best place to mount the terminal is under the dashboard, on central console or

other elements inside the cabin.

The terminal can provide two ingress protection degrees, depending on an assembly:



IP 51 – no connectors’ lid ,



IP 54 – using a connectors’ lid and corrugated cable sleeve.

Recommended corrugated sleeves (aren’t included) SLT-10/50 мм.

It is recommended to mount the tracker using a connectors’ lid and corrugated

sleeves.

A rubber burn can be installed to enhance the ingress protection. (

Figure 14

). The

arrow shows the direction for the rubber burn.

You should not pull on the rubber burn while laying it on the slot. It should be

mounted so that it does not hang out.

Содержание MT-700 ENT




























































































































































Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды

Scout MT-700 ENT, Руководство по эксплуатации

Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды