Scout MT-700 ENT Скачать руководство пользователя страница 19

Страница: 19 / 155

МТ-700 fleet tracking system



Traffic encryption

Traffic encryption option can be applied.
All the data is being send using the

AES-128 encryption

The key – is a terminal password.
To enable the function:



Enable «Traffic encryption» in terminal common settings.



Create the encryption key, by changing terminal password. The default key is

identical for all trackers, so it is not recommended to use it for traffic encryption.



Enable «Use password for access» option is SCOUT-Server settings.



Enter the key (tracker password) in the «password» in SCOUT Server settings.

Figure 9. password enable



Using the Voice call

МТ-700 PRO / МТ-700 PRO 285 provides speaker



and microphone connection for

voice calls.



SMS messages

The tracker provides SMS sending using the SCOUT Configurator.
To send the SMS open the “Modem Settings” tab (

Figure 10

Содержание MT-700 ENT




























































































































































Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды

Scout MT-700 ENT, Руководство по эксплуатации

Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды