Scout MT-700 ENT Скачать руководство пользователя страница 22

Страница: 22 / 155

МТ-700 fleet tracking system



The tracker pre-installation (SIM card and battery installation)

All action including SIM-card installment, backup battery connection

and antenna installment should be conducted only while

the terminal

powered is off.

The manufacturer is not responsible for any malfunctions that are

caused by not following these rules.

It is not recommended to install the terminal in places prone to

high temperatures – these can lead to a backup battery failure.

Before powering on and configuring the device, you should:



Take off the connectors’ lid (if it is pre-installed) by tackling 2 screws and pushing the

latches on the top side of the lid.



Take off the top lid by unscrewing the four screws from the bottom side. (

Figure 11

Figure 11. Tracker disassemble



Plug in the backup battery connector(

Figure 12

). If needed, the battery can be

unplugged to save the battery power during the tracker’s service period.



Screw the top and bottom lids together.

Latch

Top connectors’ lid

Top lid

Bottom connectors’ lid

Bottom lid

Содержание MT-700 ENT




























































































































































Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды

Scout MT-700 ENT, Руководство по эксплуатации

Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды