Scout MT-700 ENT Скачать руководство пользователя страница 30

Страница: 30 / 155

МТ-700 fleet tracking system



Antenna connection

It is forbidden to shorten, lengthen or conjoin the antennas!

Mounting the GSM antenna

GSM antenna should be mounted in a place with the best radiosignal propogation.

Appropriate options are: the inner side of the windshield or plastic interior parts.

It is not recommended to mount a GSM antenna onto the metal parts.

The distance between the antenna and the onboard wires should not be less than 5 cm.

Also it is recommended to distance the antenna from the built-in radio and other radio-

emitting devices. Mount the antenna not more than the 30 cm from the device enclosure.

Mounting the antenna on the enclosure of the device is strictly

forbidden!

Figure 27. Mounting options for GPS/GNSS antenna

Mounting GPS/GNSS antenna

GPS/GNSS antenna should be mounted so that the best open sky view is achieved.

Options for mounting the antenna:



Under the windshield ,



On the roof of the vehicle,



Holes in the bumper,



Plastic spoiler holes and other non-metal automotive upholstery parts;

Truck mounting options:



Under the wind shield,



On the roof of the vehicle.

Содержание MT-700 ENT




























































































































































Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды

Scout MT-700 ENT, Руководство по эксплуатации

Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды