Scout MT-700 ENT Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 155

background image

МТ-700 fleet tracking system

5



Overview

The following product manual (further - “Manual”) applies to an onboard monitoring unit MT-700
Lite, Mt-700 STD, MT-700 ENT, MT-700 PRO and MT-700 PRO 285(further-tracker) manufactured by
the Limited Liability Company : Осовремененные технологии мониторинга (further - LLC “CTM”).

The tracker is intended for vehicle operative control that uses vehicle-monitoring systems. The
tracker must be supplied with 12 or 24 VDC onboard voltage. The tracker is able to control
connected slave devices.

The tracker’s performance is based on using GPS/GLONASS navigation and GSM/UMTS cellular
service channels.

The GSM channel is used for the following functions: transmission of data, imputing voice calls, and
SMS commands. The SIM card must be serviceable, activated, non-locked and have the needed
packages activated ( GPRS general packet data, SMS, roaming and voice call must be activated for
the MT-700 Pro) in order to guarantee the tracker’s smooth operation.



Hardware description

The terminal has a form of a monoblock, with the GSM and GPS antennas jacks, power

and I/O jack. There is an ID nameplate on the top of the enclosure, specifying the device
version.

Available versions of the tracker are shown in Figures 1, 2, 3 и 4.

Figure 1. МТ-700 PRO / МТ-700 PRO 285

Figure 3. МТ-700 STD / МТ-700 ENT / МТ-700 Lite

Figure 4. Terminal with the connectors’ lid

«
...
3
4
5
6
7
...
»

Содержание MT-700 ENT




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT-700 ENT

Бренд: Kawai Страницы: 142

Бренд: Kawai Страницы: 10

Бренд: C-LOGIC Страницы: 4

Workstation Monitor 724

Бренд: 3M Страницы: 21

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 24

Бренд: 3M Страницы: 2

SoundPro SE Series

Бренд: 3M Страницы: 293

Бренд: Tavool Страницы: 12

Бренд: Hilti Страницы: 31

Бренд: CAS Corporation Страницы: 20

Бренд: SICK Страницы: 68

Photo Research PR-810

Бренд: Jadak Страницы: 120

Бренд: Hanna Instruments Страницы: 2

Smart Photometer System iDip 570

Бренд: eXact Страницы: 16

Бренд: Parkside Страницы: 199

Бренд: Kawai Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды