Scout MT-700 ENT Скачать руководство пользователя страница 23

Страница: 23 / 155

МТ-700 fleet tracking system

Figure 12



Prepare the SIM-card: make sure that all the needed packages are activated

(GPRS/HSDPA, SMS, voice calls, roaming, etc). Check the SIM’s balance. Turn off PIN
request if it is turned on.



Push the SIM-card extraction button to extract the SIM-tray.



Insert the SIM tray into the SIM-card aperture. Check if the tray has been fully

inserted; you should not be able to pull out the tray without pressing a button.

Figure 13. Terminal view from the connector jack



Preliminary tracker settings

You can configure the device using either local or remote “Configurator” or through SMS-

commands (see further in chapter 4).

To properly install the tracker you have to specify these settings



GPRS settings:



password,



access point.



Modem settings:



Phone number for SMS-commands.



Server connection:



IP-address,



Port.



Connection condition settings and port settings – depending on the required operational
mode and connected sensors and devices.

Terminals can be wirelessly configured and configured through SMS-commands. If the

modem correct GPRS, modem and server settings were not implemented during the mounting
process, then the remote configuration can only be accomplished through the SMS-commands.

The SCOUT employees’ phone numbers are embedded in the terminal’s white-list.

SIM extraction button

SIM-card tray

Содержание MT-700 ENT




























































































































































Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды

Scout MT-700 ENT, Руководство по эксплуатации

Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды