Rohde & Schwarz NRP18A Скачать руководство пользователя страница 121

Страница: 121 / 165

Remote Control Commands

R&S

NRPxxA(N)

121

User Manual 1177.6017.02 ─ 05

For more information, see

SYSTem:LED:COLor

Parameters:

<mode>

USER | SENSor
*RST:

SENSor

SYSTem:MINPower?

Queries the lower power measurement limit.

This value changes if

[SENSe<Sensor>:]CORRection:SPDevice:STATe

is set to

. The lower measurement limit refers to the sensor or to the combination of a sensor

and the components connected ahead of it.

Use this query to determine a useful resolution for the result display near the lower
measurement limit.

Usage:

Query only

SYSTem:PARameters?

Lists all commands with default values, limits and ranges.

Usage:

Query only

SYSTem:PARameters:DELTa?

Lists all commands that differ from the defined default status set by

*RST

on page 67.

The commands are output with default values, limits and ranges.

Usage:

Query only

SYSTem:PRESet

Triggers a sensor reset.

The command essentially corresponds to the

*RST

command, with the exception that

the settings of the following commands are persistently held:

INITiate:CONTinuous

SENSe:AVERage:TCONtrol

Usage:

Event

SYSTem:REBoot

Reboots the sensor.

Usage:

Event

Configuring the System

Содержание NRP18A






































































































































































Результаты поиска

Содержание NRP18A

Отзывы:

Похожие инструкции для NRP18A

Бренды по названию

Популярные бренды

Rohde & Schwarz NRP18A, Руководство пользователя

Результаты поиска

Содержание NRP18A

Отзывы:

Похожие инструкции для NRP18A

Бренды по названию

Популярные бренды