Rohde & Schwarz NRP18A Скачать руководство пользователя страница 18

Страница: 18 / 165

Preparing for Use

R&S

NRPxxA(N)

User Manual 1177.6017.02 ─ 05

b) Connect the power sensors to the R&S NRP

‑

Z5 sensor hub. You can connect

up to four sensors.

c) Connect the R&S NRP

‑

Z5 to the computer.

d) Connect the power sensors to the signal source.
e) Connect the delivered external power supply unit to the R&S NRP

‑

Z5 and to an

AC supply connector.

f) Connect the trigger input of the R&S NRP

‑

Z5 with a BNC cable to the trigger

source (optional).

g) Connect the trigger output of the R&S NRP

‑

Z5 with a BNC cable to the trigger

device (optional).

2. On the computer, start a software application to view the measurement results.

See

Chapter 5, "Operating Concepts"

on page 29.

3.5.2

Setting Up a LAN Connection

Requires power sensors with networking capabilities, the R&S

NRP LAN power sen-

sors.

This section describes how to connect the sensor to a LAN network and configure the
LAN interface for establishing a connection.

Electromagnetic interference (EMI) can affect the measurement results. To avoid any
impact, use category 5 cables or better.

3.5.2.1

Connecting a LAN Power Sensor and a Computer

There are different ways to connect a LAN power sensor to a computer according to
the available equipment:

Connecting to a Computer

Содержание NRP18A






































































































































































Результаты поиска

Содержание NRP18A

Отзывы:

Похожие инструкции для NRP18A

Бренды по названию

Популярные бренды

Rohde & Schwarz NRP18A, Руководство пользователя

Результаты поиска

Содержание NRP18A

Отзывы:

Похожие инструкции для NRP18A

Бренды по названию

Популярные бренды