Quantum DXi8500 Скачать руководство пользователя страница 410

Страница: 410 / 520

Chapter 9: DXi8500 Configuration
System

380

Quantum DXi8500 User’s Guide

• The source DXi management/data IP address, the source DXi

replication IP address, and the target DXi IP address are all on the

same subnet (192.168.10.x).

• To make sure the replication segment is used when communicating

with the target DXi, you must add a host route in the

Routing

Details

section on the source DXi.

In this example, you would specify the following routing details for

the replication interface on the source DXi:

•

Destination

- Use the IP address of the target DXi

(192.168.10.200).

•

Dest Netmask

- Use 255.255.255.255.

•

Dest Gateway

- Use the replication IP address of the source DXi

(192.168.10.100).

Figure 211 Interface Routing:
Example 2

Example 3: Segments on the Same Subnet and Target on a Different

Subnet

In the example below (see

Figure 212

), the DXi has two segmented

interfaces, one for data and management traffic, and one for replication

traffic:

• The source DXi management/data IP address and the source DXi

replication IP address are on the same subnet (192.168.10.x). The

target DXi IP address is on a different subnet (192.168.20.x)

Source DXi

192.168.10.x subnet

Replication IP:

Target DXi

192.168.10.100

IP: 192.168.10.200

Management/Data IP:

192.168.10.101

Содержание DXi8500









































































































































































































































































































































































































































































































































Результаты поиска

Содержание DXi8500

Отзывы:

Похожие инструкции для DXi8500

Бренды по названию

Популярные бренды

Quantum DXi8500, Руководство пользователя

Результаты поиска

Содержание DXi8500

Отзывы:

Похожие инструкции для DXi8500

Бренды по названию

Популярные бренды