Quantum DXi8500 Скачать руководство пользователя страница 197

Страница: 197 / 520

Chapter 6: DXi8500 Replication

Understanding Data Replication

Quantum DXi8500 User’s Guide

167

Caution:

A saved snapshot is necessary to recover your data at a

later time. For this reason, it is not enough to simply enable

replication for a share or partition. You must also configure

a replication schedule (recommended) or perform manual

replication on a regular basis to send snapshots of the

share or partition to the target system.

If the source system ever becomes unavailable, you can recover the

share or partition on the target system using a saved snapshot. After

you recover a share or partition, it is recreated on the target system and

is available for use. Once the source system becomes available again,

you can perform a failback operation to restore the share or partition to

its original location.

Directory/File or

Cartridge Based

Replication

Like replication, Directory/File or Cartridge Based Replication sends data

from a NAS share or VTL partition to another system where it can be

accessed. However, Directory/File or Cartridge Based Replication differs

in a number of important ways:

• Both replication and Directory/File or Cartridge Based Replication

must be enabled for the share or partition.

• A unique Sync ID is used to associate the replicated share or

partition on the source system with the share or partition that will

receive the replicated data on the target system.

• You do not need to schedule or manually perform Directory/File or

Cartridge Based Replication through the remote management

console. Instead, replication is triggered when a file is closed or a

period of time after it is modified (NAS shares), or when a tape

cartridge is unmounted (VTL partitions).

Note:

For CIFS shares, a file is replicated immediately after it is

closed. For NFS shares, a file is replicated after it has been

idle (not accessed) for several minutes.

• After directories and files or cartridges are replicated using

Directory/File or Cartridge Based Replication, they are automatically

recovered on the target system and are immediately available for

use. There is no need to first recover the share or partition to access

its data.

Содержание DXi8500









































































































































































































































































































































































































































































































































Результаты поиска

Содержание DXi8500

Отзывы:

Похожие инструкции для DXi8500

Бренды по названию

Популярные бренды

Quantum DXi8500, Руководство пользователя

Результаты поиска

Содержание DXi8500

Отзывы:

Похожие инструкции для DXi8500

Бренды по названию

Популярные бренды