Quantum DXi8500 Скачать руководство пользователя

Страница: 341 / 520

Chapter 9: DXi8500 Configuration

Replication

Quantum DXi8500 User’s Guide

311

In the

Source IP Address

field, enter the IP address that is used to

uniquely identify the source DXi to the target. This may be different

than the actual network IP address of the source DXi.
If the target system is at DXi 2.1 Software or higher, the

Source IP

Address

field is not required. If the target system is at DXi 2.0.1.x

Software or below, then you must enter the IP address by which the

target system recognizes the source system. The default value is

0.0.0.0

Note:

The

Source IP Address

field does not accept fully qualified

domain names. You must enter a valid IP address. Make

sure this IP address is configured in the allowable sources

list on the target DXi.

Note:

When configuring segmented network interfaces, if the

source DXi replication, data, and management interfaces

are on the same subnet, you must add a host route on the

source DXi to make sure the replication interface is

correctly selected when replicating data to the target DXi

(see

Understanding Interface Routing

on page 378).

(Optional) Leave the

Use Encryption

check box selected to enable

encryption when sending replication data to the target system. Or

clear the

Use Encryption

check box to disable encryption when

sending replication data to the target system.
If encryption is enabled, select an encryption strength (

128-bit

256-bit

). Using 256-bit encryption (default) provides a stronger

level of security but may have an impact on system performance in

some situations.

Caution:

Select 128-bit encryption if you are sending data to a

DXi running a system software version prior to DXi 2.1

Software.

Note:

Encryption is enabled by default. However, for best

performance, if your data network is already secured, you

should clear the

Use Encryption

check box.

(Optional) Select the

Enable system throttling

check box to enable

a constant replication throttle for the system. Or clear the

Enable

Содержание DXi8500









































































































































































































































































































































































































































































































































Результаты поиска

Содержание DXi8500

Отзывы:

Похожие инструкции для DXi8500

Бренды по названию

Популярные бренды

Quantum DXi8500, Руководство пользователя

Результаты поиска

Содержание DXi8500

Отзывы:

Похожие инструкции для DXi8500

Бренды по названию

Популярные бренды