ProMinent DULCOTROL Скачать руководство пользователя страница 83

Страница: 83 / 144

Minent

Page 83

8.7.2

DULCOTEST

ICT 2 Inductive Conductivity Sensor, Commissioning

8.7.2.1

DULCOTEST

ICT 2 Inductive Conductivity Sensor, Assembly

Assembly

WARNING

• Ensure that the axes of the sensor and pipe are per pen dicular to one another. Ensure

that the thread is aligned correctly. It will otherwise affect the stability of the measure-
ment points in pressurised processes.

• The axis through the hole of the sensor tip must line up with the pipe axis.

• The sensor tip must be covered by the water sample at all times during measurement.

• The measurement results will otherwise be incorrect.

IMPORTANT

If you later require measurement accuracy better than 10 %, fi t a tap near the sensor to

take water samples.

The sensor ICT 2 can be directly installed in tanks and pipes or via a ﬂ ange and/or an in-line

probe housing.

Before installing the sensor, carry out commissioning up to and including zero point calibration.

Insert the sensor into the opening of the media tubing or the tank (the ﬂ at seal must sit on the

inside of the tubing or tank). If used in ﬂ owing media, the sensor tip bore must be placed in
the centre of the tube cross section.

Rotate the sensor so that the bore of the sensor tip is facing in the direction of the ﬂ ow.

Tighten the union nut.

8.7.2.2

DULCOTEST

ICT 2 Inductive Conductivity Sensor, Electrical Installation

IMPORTANT

• Connect the sensor only when the mains power supply is switched off.

• Do not shorten the connection lead. The measurement result will otherwise be in cor-

rect. The warranty is void in this case.

• If using a DULCOMETER

D1C controller use a mains cable with earth lead! The sensor

cable screening must be earthed by the earth lead if there is potential inter ference!

• Install according to the relevant national directives.

Break open the large opening in the middle of the base of the DULCOMETER

D1C housing

(see Operating instructions DULCOMETER

D1C, part 1)

Screw in a 13.5 skintop connector (supplied with the DULCOMETER

D1C controller)

Cut off the brown and the yellow cable

Earth the total cable screen via the power lead of the mains cable of the DULCOMETER

D1C

controller if there is potential inter ference. For this purpose crimp e.g. a screen connector onto
the total screen.

Connect the sensor to the DULCOMETER

D1C controller in accordance with the terminal

connection diagram

Tighten the skintop connector until watertight, ensuring that there is still sufﬁ cient cable inside

the DULCOMETER

D1C controller.

Inductive Conductivity

BA_DR_002_02_09_GB_Cooling.indd 83

24.02.2009 11:56:08 Uhr

Содержание DULCOTROL

















































































































































Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды

ProMinent DULCOTROL, Общие инструкции по эксплуатации

Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды