ProMinent DULCOTROL Скачать руководство пользователя страница 130

Страница: 130 / 144

Minent

Page 130

8.11.2.2

DULCOTEST

CDE Sensor and DULCOTEST

Sensor PHEP or PHER for

pH, Electrical Installation

Installation

DULCOTEST

CDE Chlorine Dioxide Sensor

IMPORTANT

• The sensor is not electrically isolated from the sample water. All other elements must

be isolated! The controller must be isolated both from the sensor and from the supply
voltage!

• The supply voltage must not fall below 16 V DC, even for a short period! The current

source must able to sustain 35 mA at a min. 16 V DC! Insuffi cient supply voltage will
result in an inaccurate reading!

• After the electrical connection of the sensor, the sensor has to be inserted into the

sample water which has to contain chlorine dioxide.

The sensor incorporates a passive 4-20 mA two-wire interface, i.e. the power supply is provided

externally e.g. via the controller.

• Safety requirements are automatically met if the sensor is connected to a ProMinent

control-

ler (e.g. DULCOMETER

D1C).

• Do not switch off the measuring system when in intermittent use!

If necessary, dosing equipment should be timer-controlled!

Electrical

Installation

Rotate the sensor adapter anticlockwise by 90 º and remove (bayonet ﬁ tting).

Unscrew the PG-7 threaded connector tensioning screw and insert the signal cable leading

from the controller.

Strip the ends of the cable and attach to the two-wire connector: 1 = positive, 2 = negative

Insert approx. 5 cm of signal cable into the sensor and tighten the PG-7 threaded connector

tensioning screw.

Insert the sensor adapter completely into the housing and screw together carefully to prevent

damage to the ends of the bayonet connector.

Electrical

connection

sensor

1 2

5 cm

Sensor

Connect the DULCOTEST

PHEP or PHER sensor for pH with the marked cable of the respective

controller DULCOMETER

D2C.

pH/Chlorine Dioxide

BA_DR_002_02_09_GB_Cooling.indd 130

24.02.2009 11:56:11 Uhr

Содержание DULCOTROL

















































































































































Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды

ProMinent DULCOTROL, Общие инструкции по эксплуатации

Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды