ProMinent DULCOTROL Скачать руководство пользователя страница 28

Страница: 28 / 144

Minent

Page 28

8.1.2

DULCOTEST

CLE Chlorine Sensor for Free Chlorine, Commissioning

8.1.2.1

DULCOTEST

CLE Chlorine Sensor for Free Chlorine, Assembly

Assembly

Pouring

electrolyte

IMPORTANT

• Do not touch, damage or bring into contact with greasy substances the white mem-

brane or the electrodes on the electrode shaft. The sensor will not, in such cases, work
accurately.

• Replace the membrane cap or send the sensor to ProMinent to have the electrodes

cleaned.

NOTE

Carry out the following actions over a washbasin.

Remove the red cap completely from the nozzle and cut the nozzle at the marked position to

open the nozzle canal.

Remove the membrane cap cover and unscrew the membrane cap from the electrode shaft.

Rinse the membrane cap and the electrode with a little electrolyte.

Fill the membrane cap up to the rim with electrolyte.

Remove air bubbles by lightly tapping the membrane cap on an even surface.

Assembling membrane cap

Place the electrode shaft upright onto the ﬁ lled membrane cap and twist until the thread bites.

Rotate the electrode shaft until the vent hole is pointing upwards.

Slowly screw in the membrane cap by hand up to the stop. Excess electrolyte will seep out of

the vent hole as you screw the parts together.

Rinse away the excess electrolyte from your ﬁ ngers and from the sensor under running water.

There should be no air left in the membrane cap/electrolyte. Repeat the above steps if there is

still air present.

Assembling

sensor

IMPORTANT

When removing and inserting the sensor from or into the in-line probe housing, do so

slowly to prevent damaging the membrane.

The sensor must be kept damp after commissioning, e.g. the in-line probe housing

should never be allowed to run dry.

Assemble the sensor as described in the operating instructions manual for the in-line probe

housing.

8.1.2.2

DULCOTEST

CLE Chlorine Sensor for Free Chlorine, Electrical

Installation

IMPORTANT

Do not switch the measuring system off when using intermittently.

If necessary, use a timer to switch on metering equipment.

When connecting to a

ProMinent

device

Safety conditions at the interface are automatically fulﬁ lled when connecting to ProMinent

controllers (e.g. DULCOMETER

D1C, DMT, CLD).

The CLE 3-mA is a sensor with a passive 4-20 A two-wire interface, i.e. the power supply is

external, e.g. via the controller.

Free Chlorine

BA_DR_002_02_09_GB_Cooling.indd 28

24.02.2009 11:56:04 Uhr

Содержание DULCOTROL

















































































































































Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды

ProMinent DULCOTROL, Общие инструкции по эксплуатации

Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды