ProMinent DULCOTROL Скачать руководство пользователя страница 84

Страница: 84 / 144

Minent

Page 84

Inductive Conductivity

8.7.2.3

DULCOTEST

ICT 2 Inductive Conductivity Sensor, Running-In

The sensor DULCOTEST

ICT 2 inductive conductivity can be readily used for further measures

such as calibration and measurement without requiring any running-in.

8.7.2.4

DULCOTEST

ICT 2 Inductive Conductivity Sensor, Calibration

Presettings

Check

ﬁ rst that the sensor is correctly connected to the DULCOMETER

D1C (do not open the

sensor).

Check that the right sensor type has been selected.

type of sensor

setting ?

type of sensor :

ICT 2

sensor data

are changed!

Set the measurement range of the sensor.

IMPORTANT

Check settings in all menus when changing the range allocation.

Zero Point Calibration

setting ?

meas. parameter

Access to all setting menus can be blocked with an access code !

cc :

mr :

15 mS/cm 23.8

20 mS/cm

1.120/cm

2.10%

mr: meas. range

cc: cellconstant

: temperature-

coefficient

mr 2 : 200

S/cm

cc 2 : 1.120 /cm

2.10% /

1106

S/cm 25.0

cali. zero point

PAR 1

cali. zero point

probe in air!

accept value?

S/cm

please wait!

= automatic timing

IMPORTANT

• The zero point must be calibrated during commissioning.

• The zero point must be calibrated if the measurement range is changed.

• Calibrate the zero point only when the sensor tip is completely dry.

• Calibrate the zero point in the air when dismantled only.

• Hold the sensor tip more than 40 mm away from all objects during calibration.

• Calibrate the zero point before the slope.

To calibrate the zero point of the sensor, dismantle the sensor and then completely dry the

sensor tip and the sensor shaft.

Select the ﬁ rst menu option in the “cali. zero point” in the setting menu and wait approx. 30 s

until the measured value is stable – then press Enter.

BA_DR_002_02_09_GB_Cooling.indd 84

24.02.2009 11:56:08 Uhr

Содержание DULCOTROL

















































































































































Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды

ProMinent DULCOTROL, Общие инструкции по эксплуатации

Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды