ProMinent DULCOTROL Скачать руководство пользователя страница 140

Страница: 140 / 144

Minent

Page 140

Decommissioning and Disposal

CAUTION

• The controller may only be disconnected from the mains supply by a qualifi ed elec tri-

cian!

•

Thoroughly

fl ush the sample water line with a suitable medium (see data safety sheet)!

• Please also read the operating instructions of the controllers and fi ttings and any other

existing assemblies such as sensors, sample water pump … !

• Also in case of a short time of decommissioning (up to 12 h): Observe the operating

instructions of the sensor!

• Please observe the safety data sheets for the media involved in your process!

In case of temporary or long-term decommissioning. Close the ball valves such that the

sensors remain surroanded by sample water.

12.1

Temporary or Long-Term Decommissioning

CAUTION

• Please observe the safety data sheets for the media involved in your process!

• Please also read the operating instructions of the controllers and fi ttings and any other

existing assemblies such as sensors, sample water pump … !

12.2

Final

Decommissioning

CAUTION

• Please observe the safety data sheets for the media involved in your process!

• Please observe the respective applicable local regulations!

• In Germany, used parts can be disposed of at the municipal collection points of the

cities and municipalities.
You may return the used parts to the ProMinent Dosiertechnik GmbH, Heidelberg,
against a low fee and prepaid postage.

• Please also read the operating instructions of the controllers and fi ttings and any other

existing assemblies such as sensors, sample water pump … !

• The electrolyte of the sensors can be caustic!

• Collect leaking electrolyte. Wear suitable gloves and safety goggles.

• Remove contaminations with a lot of water. Dispose of waste water in a way harmless to

the environment.

Replacement

Parts

Please also note the listings in the operating instructions of the controllers and ﬁ ttings and any

other existing assemblies such as sensors, sample water pump … ! Any other replacement parts
can be ordered from our customer service.

Decommissioning and Disposal / Replacement Parts

Designation

Part number

Cartridge housing

1031209

Filter complete 10 μm

1031210

Filter complete 100 μm

1031211

Pressure reducer with indicator for ﬂ ushing and cooling water

1031212

Heat exchanger

1031213

Sample water pump + adapter

1023089

BA_DR_002_02_09_GB_Cooling.indd 140

24.02.2009 11:56:12 Uhr

Содержание DULCOTROL

















































































































































Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды

ProMinent DULCOTROL, Общие инструкции по эксплуатации

Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды