ProMinent DULCOTROL Скачать руководство пользователя страница 13

Страница: 13 / 144

Minent

Page 13

Safety Chapter

WARNING

•

Hazardous

substances!

• Hazards from contact, inhalation or other contamination with/by substances or media!

• Observe the safety data sheet of the used substance/media.

• The operator of the DULCOTROL

measuring/control station is responsible for the fact

that the safety data sheets are available and up-to-date.

WARNING

• Unexpected start of the DULCOTROL

measuring/control station after failure, malfunc-

tion of the control/voltage supply or as intended action because of a control process!

• Hazards from unexpected actions of the stations!

• In case of malfunction/failure of the control or voltage supply, the DULCOTROL

meas-

uring/control station is to be disconnected from the voltage supply. For further informa-
tion see the operating instructions of the DULCOMETER

D1C units and sensors.

WARNING

•

Operating

error!

• Hazards from operating errors!

•

The

DULCOTROL

measuring/control stations may only be operated by suffi ciently

qualifi ed and trained personnel.

WARNING

• Electrical hazards from lightning!

• Hazards from overvoltage because of lightning stroke into external installations which

are connected to the DULCOTROL

measuring/control station.

• Do neither directly nor indirectly use the DULCOTROL

measuring/control station for

use in the open.

• Provide for suffi cient potential to ground when installing electrical components.

NOTE

• Protect the DULCOTROL

measuring/control stations against unauthorised access!

• Please also read the operating instructions of the controllers and fi ttings and any other

existing assemblies such as sensors, sample water pump … !

• Please observe the resistance of the materials of all assemblies in contact with

the media. (see e.g. the ProMinent resistance list in the product catalogue or at
www.prominent.com.)!

• Protect the DULCOTROL

measuring/control station against direct exposure to the sun

and other UV sources!

• Please observe the basic rules of ergonomic principles!

1.3

Information for Emergencies

• Electrical emergency: Switch off the DULCOTROL

measuring/control station via the mains

switch, at the terminal box or at the place speciﬁ ed by the operator!

• Hydraulical emergency: Close the DULCOTROL

measuring/control station at the inlet- or

outlet-side ball valve, observe the safety data sheet of the medium!

BA_DR_002_02_09_GB_Cooling.indd 13

24.02.2009 11:56:02 Uhr

Содержание DULCOTROL

















































































































































Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды

ProMinent DULCOTROL, Общие инструкции по эксплуатации

Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды