ProMinent DULCOTROL Скачать руководство пользователя страница 107

Страница: 107 / 144

Minent

Page 107

pH/Chlorine

Assembling

sensor

IMPORTANT

• Depressurise the system before inserting the sensor into the in-line probe housing.

Close the stop valves before and after the in-line probe housing.

• Insertion and withdrawal of the sensor into or out of the in-line probe housing should be

carried out slowly.

• Do not exceed the maximum operating pressure of 1 bar.

• Do not allow the fl ow to fall below the minimum rate of 30 l/h. Monitor the fl ow with the

connected measuring device/controller. If the sensor‘s signal is used for con trolling,
switch off the controller or adjust it to constant load when the fl ow rate falls below the
lower limit.

• Avoid installations which allow air bubbles to enter the sample water. Air bubbles

clinging to the sensor membrane can lower the resultant measured value and cause
incorrect dosing within the control system.

Fitting the sensor in

the in-line probe housing

Note also the instructions and safety guidelines in the operating instructions of the in-line probe
housing.

DLG III

Slide the O-ring from below over the sensor up to the clamping ring.

Insert the sensor into the DLG III.

Fix the sensor tightly by screwing in the plug.

DGM

Slide the O-ring from below over the sensor up to the clamping ring. Leave a ﬂ at washer inside

the DGM.

Insert the sensor in the DGM and screw on the plug until the O-ring seals. The clamping ring

determines the installation depth of the sensor.

Assembly

Installation of the DULCOTEST

PHEP or PHER sensor for pH

Remove the blanking plug of the respective measuring module at the ﬁ ttings of the measuring/

control station DULCOTROL

and install the DULCOTEST

PHEP or PHER sensor for pH.

8.9.2.2

DULCOTEST

CTE Sensor for Total Chlorine and DULCOTEST

Sensor

PHEP or PHER for pH, Electrical Installation

DULCOTEST

CTE sensor for total chlorine

General Safety Guidelines

IMPORTANT

Install in such as way as to ensure a totally reliable, uninterrupted power supply to the

controller. Too low a voltage supply can cause measuring failures, which may result in
dangerous overdosing within a control system.

The CTE 1-mA sensor has a passive 4-20 mA two-wire interface. The power supply is provided

externally or by the controller. When the sensor is connected to the DULCOMETER

D1C

controller the interface’s safety require ments are met automatically.

IMPORTANT

For electrical connection of the sensor to the controller, only use wires with a diameter of
4 mm.

Electrical

Installation

Turn the top part of the sensor a quarter of a turn anticlockwise and remove.

Remove the outer isolation of the cable for about 5 cm from the end so that the two wires

appear.

BA_DR_002_02_09_GB_Cooling.indd 107

24.02.2009 11:56:10 Uhr

Содержание DULCOTROL

















































































































































Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды

ProMinent DULCOTROL, Общие инструкции по эксплуатации

Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды