ProMinent DULCOTROL Скачать руководство пользователя страница 12

Страница: 12 / 144

Minent

Page 12

Safety Chapter

Safety

Chapter

1.1

Identifi cation of the Notes on Safety

The following terms are used in the present operating instructions to indicate the various severity

levels of the danger:

DANGER

Characterizes a possibly hazardous situation. There is a danger of death or serious injuries

if these notes are disregarded.

WARNING

Characterizes a possibly hazardous situation. Your life is in danger and there is a danger of

serious injury or death if these notes are disregarded!

CAUTION

Characterizes a possibly hazardous situation. There is a danger of slight or minor injury or

damage to property if these notes are disregarded.

NOTE

A note provides important notes for the correct functioning of the unit or is to facilitate

your work.

The following warning signs are used in the present operating instructions to indicate different

types of the danger:

Warning of danger area

Warning of hazardous electrical voltage

Warning of caustic substances

Warning of hot surfaces

Warning of unexpected start

1.2

General Notes on Safety

WARNING

•

Live

parts!

• Disconnect from mains plug before opening the housing.

• De-energise damaged, defective or manipulated units by disconnecting the mains plug.

WARNING

•

Hot

surfaces!

• Risk of burning at the surfaces of the measuring station.

• For sample water > 55 °C, a temperature monitor with solenoid valve has to be installed

to protect the DULCOTROL

measuring/control station. The temperature monitor is not

included in the scope of delivery and must be installed by the customer.

• Suitable measures must be taken to prevent that nobody gets into contact with hot

surfaces.

BA_DR_002_02_09_GB_Cooling.indd 12

24.02.2009 11:56:02 Uhr

Содержание DULCOTROL

















































































































































Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды

ProMinent DULCOTROL, Общие инструкции по эксплуатации

Результаты поиска

Содержание DULCOTROL

Отзывы:

Похожие инструкции для DULCOTROL

Бренды по названию

Популярные бренды