ProMinent DULCOTROL Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 144

background image

Pr

o

Minent

®

Page 69

Redox/ORP

8.5.2

DULCOTEST

®

Sensor for Redox/ORP, Commissioning

8.5.2.1

DULCOTEST

®

Sensor for Redox/ORP, Assembly

Assembly

Prior to commissioning, the protective cap or quiver must be removed from the glass or metal

electrode. The glass or metal electrode must be free of contaminations, oils and greases. The
diaphragm of the reference electrode must also be free of deposits, contaminations and crys tal li-
sa tions. For this reason, the electrodes should not be touched with bare hands. Should con tam i-
na tions exist, please see “Cleaning and Care” in the individual operating instructions.

8.5.2.2

DULCOTEST

®

Sensor for Redox/ORP, Electrical Installation

Electrically connect the DULCOTEST

®

sensor for Redox/ORP with the marked cable of the

respective controller D1C.

8.5.2.3

DULCOTEST

®

Sensor for Redox/ORP, Running-In

The

DULCOTEST

®

sensor for Redox/ORP must not be run-in. The DULCOTEST

®

sensor for

Redox/ORP can be readily used.

8.5.2.4

DULCOTEST

®

Sensor for Redox/ORP, Calibration

Having connected the sensor to the transmitter by means of the sensor cable (taking care that

connectors and cable remain absolutely dry), dip the sensor into a redox standardizing solution,
e.g. of 465 mV. The reading should reach or exceed this value within not more than 30 seconds.
If the reading rises rather sluggishly or falls short more than 20 mV, clean the sensor as described
and repeat check. If again unsuccessful, replace the sensor with a new one.

D1C2-011-Redox-GB

Permanent display 1

Permanent display 2
only with control
(w = setpoint)

mea. val.
fd. fwd.:
reg. val.:

750 mV

w:

750 mV

70 %
59 %

Positive values of setting variable:
Negative values of setting variable:

Oxidant agent
Reducing agent

mV

750

Checking the Redox/ORP Sensor

During calibration, the D1C sets the command outputs to “0”. Exception: if a basic load or a

manual control variable was set, these are maintained during calibration. The standard signal
outputs mA (measuring value or correction value) are frozen. The measured value or the standard
buffer value 220 mV or 465 mV is proposed as the buffer value; this value is adjustable (arrow
keys). After everything has been checked, all error tests which refer to the measured value are
restarted.

D1C2-012-Redox-GB

= automatic timing

check probe
ORP

check probe
ORP
probe in buffer

460 mV

check probe
measurement act.
please wait !

460 mV

check probe
ORP
value:

buffer:

460 mV
465 mV

Permanent display 1

BA_DR_002_02_09_GB_Cooling.indd 69

BA_DR_002_02_09_GB_Cooling.indd 69

24.02.2009 11:56:07 Uhr

24.02.2009 11:56:07 Uhr

«
...
67
68
69
70
71
...
»

Содержание DULCOTROL

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DULCOTROL

Q-SYS Core 110f

Бренд: QSC Страницы: 2

Бренд: Rain Bird Страницы: 138

Бренд: Absima Страницы: 5

Бренд: Danfoss Страницы: 2

Бренд: tell Страницы: 11

Бренд: mikroElektronika Страницы: 3

Бренд: Window Master Страницы: 7

Бренд: Dejero Страницы: 24

Бренд: TradeQuip Страницы: 9

Бренд: WINDY NATION Страницы: 16

Бренд: Kaba Mauer Страницы: 10

Бренд: Parallax Страницы: 3

Бренд: Aqua Creek Страницы: 3

Бренд: Dantherm Страницы: 36

SCENE MASTER - V1.0

Бренд: JBSYSTEMS Light Страницы: 24

Бренд: CALEFFI Страницы: 14

Бренд: Heat Controller Страницы: 10

Бренд: WAGO Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды