ProMinent DULCOTROL Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 144

background image

Pr

o

Minent

®

Page 137

Deviating Settings of the Controller

9.2

Setting of the Pause Contact for Flow Monitoring

Flow

Monitoring

IMPORTANT

The

fl ow of the sample water must be monitored because varying or faulty readings may

result in case of insuffi cient or no fl ow!

For a DULCOMETER

®

D1C as single unit, the ﬂ ow monitoring is designed as make contact as

standard (default). A cable break cannot be monitored.

For the DULCOMETER

®

D1C of the measuring/control stations DULCOTROL

®

cooling water, this

ﬂ ow monitoring is factory-designed as break contact. In case of cable break or if a certain
minimum ﬂ ow rate to be set is andershot, an alarm is triggered. The controlling goes to “Pause”
and the display of the controller D1C shows “Pause”.

The minimum ﬂ ow rate value can be adjusted by moving the limit value contact at the ﬂ ow meter

to the top and bottom, resp.
For all types of the ﬂ ow monitoring, the alarm relay is activated:

alarm relay
active

Access to all setting menus can be blocked with an access code !

general setting
information

identcode: D1CA
DxFxxxxxxxxxx
software version
D1C-C1 FW-5.00

access c.:

5000

operating menu:
= english
= complete

- pause normal
- active... open
- alarm on
- td: 0 min

D1C2-CIO2-028-GB

Settings menu

Cone in the

Maximum limit Alarm relay

Display

“Pause Contact”

fl ow meter

value contact

“active open”

top

closed

off

bottom

open

on

“Pause ”

BA_DR_002_02_09_GB_Cooling.indd 137

BA_DR_002_02_09_GB_Cooling.indd 137

24.02.2009 11:56:12 Uhr

24.02.2009 11:56:12 Uhr

«
...
135
136
137
138
139
...
»

Содержание DULCOTROL

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DULCOTROL

Бренд: Fairchild Страницы: 2

Бренд: Fagor Страницы: 103

Бренд: B&R Industries Страницы: 89

Бренд: BADLANDS Страницы: 2

Бренд: eclisse Страницы: 40

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

Бренд: Tamas Страницы: 12

Бренд: Tait Страницы: 3

Бренд: Brähler Systems Страницы: 25

Бренд: Monster Central Страницы: 13

Бренд: Rain Bird Страницы: 18

Бренд: TWR Lighting Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды